AD 2000-08-19 Airworthiness Directives; Boeing Model 727 and 727C Series Airplanes

Models named: 727, 727C series. Read the applicability below — it usually turns on serial or part numbers too.

Model 727 and 727C series airplanes, line numbers 153, 290, and 339 inclusive; certificated in any category. Note 1: This AD applies to each airplane identified in the preceding applicability provision, regardless of whether it has been modified, altered, or repaired in the area subject to the requirements of this AD. For airplanes that have been modified, altered, or repaired so that the performance of the requirements of this AD is affected, the owner/operator must request approval for an alternative method of compliance in accordance with paragraph (b) of this AD. The request should include an assessment of the effect of the modification, alteration, or repair on the unsafe condition addressed by this AD; and, if the unsafe condition has not been eliminated, the request should include specific proposed actions to address it.

Required as indicated, unless accomplished previously. To prevent fatigue cracking of the body skin at the forward corners of the mid-galley door hinge cutouts, which could result in reduced structural integrity of the fuselage and consequent loss of cabin pressurization, accomplish the following: One-Time Inspections (a) Prior to the accumulation of 60,000 total flight cycles, or within 3,000 flight cycles after the effective date of this AD, whichever occurs later, perform a one-time detailed visual inspection and a high frequency eddy current inspection of the exterior body skin located adjacent to the forward corners of the mid-galley door hinge cutouts for cracking in accordance with Boeing Service Bulletin 727-53-0054, Revision 1, dated November 16, 1989. Note 2: For the purposes of this AD, a detailed visual inspection is defined as: “An intensive examination of a specific structural area, system, installation, or assembly to detect damage, failure, or irregularity. Available lighting is normally supplemented with a direct source of good lighting at an intensity deemed appropriate by the inspector. Inspection aids such as mirrors, magnifying lenses, etc. may be used. Surface cleaning and elaborate access procedures may be required.” Repairs and Modification (1) If no cracking is found during any inspection, prior to further flight, modify the body skin at the forward corners of the mid-galley door hinge cutouts, in accordance with Boeing Service Bulletin 727-53-0054, Revision 1, dated November 16, 1989. No further action is required by this AD. (2) If any cracking is found during any inspection, prior to further flight, accomplish the requirements of either paragraph (a)(2)(i) or (a)(2)(ii) of this AD, as applicable. (i) If any crack is less than or equal to 1.00 inch, accomplish the repair and modification in accordance with Boeing Service Bulletin 727-53-0054, Revision 1, dated November 16, 1989. No further action is required by this AD. (ii) If any crack is greater than 1.00 inch, accomplish the repair and modification in accordance with a method approved by the Manager, Seattle Aircraft Certification Office (ACO), FAA, Transport Airplane Directorate; or in accordance with data meeting the type certification basis of the airplane approved by a Boeing Company Designated Engineering Representative who has been authorized by the Manager, Seattle ACO, to make such findings. For a repair method to be approved by the Manager, Seattle ACO, as required by this paragraph, the Manager's approval letter must specifically reference this AD. No further action is required by this AD. Note 3: Accomplishment of the actions required by AD 90-06-09, amendment 39-6488, is considered acceptable for compliance with this AD. Alternative Method of Compliance (b) An alternative method of compliance or adjustment of the compliance time that provides an acceptable level of safety may be used if approved by the Manager, Seattle ACO, FAA, Transport Airplane Directorate. Operators shall submit their requests through an appropriate FAA Principal Maintenance Inspector, who may add comments and then send it to the Manager, Seattle ACO. Note 4: Information concerning the existence of approved alternative methods of compliance with this AD, if any, may be obtained from the Seattle ACO. Special Flight Permits (c) Special flight permits may be issued in accordance with sections 21.197 and 21.199 of the Federal Aviation Regulations (14 CFR 21.197 and 21.199) to operate the airplane to a location where the requirements of this AD can be accomplished. Incorporation by Reference (d) Except as provided by paragraph (a)(2)(ii) of this AD, the actions shall be done in accordance with Boeing Service Bulletin 727-53-0054, Revision 1, dated November 16, 1989. This incorporation by reference was approved by the Director of the Federal Register in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. Copies may be obtained from Boeing Commercial Airplane Group, P.O. Box 3707, Seattle, Washington 98124-2207. Copies may be inspected at the FAA, Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton, Washington; or at the Office of the Federal Register, 800 North Capitol Street, NW., suite 700, Washington, DC. Effective Date (e) This amendment becomes effective on June 5, 2000. Issued in Renton, Washington, on April 19, 2000. Donald L. Riggin, Acting Manager, Transport Airplane Directorate, Aircraft Certification Service. [FR Doc. 00-10287 Filed 4-28-00; 8:45 am] BILLING CODE 4910-13-U