AD 2000-10-17 Airworthiness Directives; Boeing Model 747 Series Airplanes Equipped With Pratt & Whitney JT9D-70 Series Engines

Models named: 747 series. Read the applicability below — it usually turns on serial or part numbers too.

Model 747 series airplanes equipped with Pratt & Whitney JT9D-70 series engines; certificated in any category. Note 1: This AD applies to each airplane identified in the preceding applicability provision, regardless of whether it has been modified, altered, or repaired in the area subject to the requirements of this AD. For airplanes that have been modified, altered, or repaired so that the performance of the requirements of this AD is affected, the owner/operator must request approval for an alternative method of compliance in accordance with paragraph (g) of this AD. The request should include an assessment of the effect of the modification, alteration, or repair on the unsafe condition addressed by this AD; and, if the unsafe condition has not been eliminated, the request should include specific proposed actions to address it.

Required as indicated, unless accomplished previously. To prevent inadvertent deployment of a thrust reverser during flight and consequent reduced controllability of the airplane, accomplish the following: Inspection/Repair (a) Within 200 flight hours or 50 flight cycles after the effective date of this AD, whichever occurs later: Inspect the thrust reverser wiring on each engine to detect discrepancies, in accordance with Boeing Service Bulletin 747-78A2149, Revision 1, dated May 9, 1996, or Revision 2, dated August 29, 1996. Prior to further flight, repair any discrepancy, in accordance with the service bulletin. Modification and Tests (b) Within 5,000 flight hours or 500 flight cycles after the effective date of this AD, whichever occurs later: Accomplish the thrust reverser wiring modification on each engine in accordance with Boeing Service Bulletin 747-78A2149, Revision 1, dated May 9, 1996, or Revision 2 dated August 29, 1996. (1) Concurrent with accomplishment of Boeing Service Bulletin 747-78A2149, Revision 1 or Revision 2: Accomplish the modification of the thrust reverser control system wiring specified in Rohr Service Bulletin TBC-CNS 78-32, Revision 1, dated August 20, 1996. (2) Prior to further flight following accomplishment of the modification specified in paragraphs (b) and (b)(1): Perform an operational test of the thrust reverser wiring on each engine to detect discrepancies in accordance with Boeing Service Bulletin 747-78A2149, Revision 1, dated May 9, 1996, or Revision 2 dated August 29, 1996. Prior to further flight, correct any discrepancy detected, in accordance with the service bulletin. Repetitive Inspections and Tests (c) Perform the inspections and tests of the thrust reverser control and indication system to detect discrepancies at the times specified in paragraphs (c)(1) and (c)(2) of this AD, in accordance with Boeing Alert Service Bulletin 747-78A2159, dated May 18, 1995. (1) Within 90 days after the effective date of this AD, inspect in accordance with Part III, “1,000 Flight Hour Inspections” of the Accomplishment Instructions of the alert service bulletin. Repeat at intervals not to exceed 1,000 flight hours until accomplishment of paragraph (f) of this AD. (2) Within 1,500 flight hours or 4 months after the effective date of this AD, whichever occurs later, inspect and test in accordance with Part III, “18 Month Thrust Reverser System Checks” of the Accomplishment Instructions of the alert service bulletin. Repeat at intervals not to exceed 18 months until accomplishment of paragraph (e) of this AD. Corrective Actions (d) If any inspection or test required by paragraph (c) of this AD cannot be successfully performed as specified in the referenced service bulletin, or if any discrepancy is detected during any inspection or test, prior to further flight, repair in accordance with Boeing Alert Service Bulletin 747-78A2159, dated May 18, 1995. Additionally, prior to further flight, any failed inspection or test required by paragraph (c) of this AD must be repeated and successfully accomplished. Terminating Action (e) Accomplish the requirements of paragraphs (e)(1) and (e)(2) of this AD at the times specified in those paragraphs. Accomplishment of these actions constitutes terminating action for the repetitive inspections and tests required by paragraph (c) of this AD. (1) Within 36 months after the effective date of this AD: Install an additional locking system on each engine thrust reverser in accordance with the Accomplishment Instructions of Boeing Service Bulletin 747-78-2153, Revision 1, dated November 27, 1996. (2) Prior to or concurrent with accomplishment of Boeing Service Bulletin 747-78-2153, Revision 1: Accomplish the installation of provisional wiring for the locking system on the thrust reversers in accordance with Boeing Service Bulletins 747-78-2135, dated August 31, 1995; and 747-78A2149, Revision 1, dated May 9, 1996, or Revision 2, dated August 29, 1996. Additionally, concurrent with accomplishment of Boeing Service Bulletin 747-78-2153, Revision 1, accomplish the installation of the provisional wiring described previously in accordance with Rohr Service Bulletin TBC-CNS 78-33, Revision 1, dated August 20, 1996. Repetitive Functional Tests (f) Within 4,000 hours time-in-service after accomplishment of paragraph (e) of this AD: Perform a functional test to detect discrepancies of the additional locking system on each thrust reverser, in accordance with Appendix 1 (including Figures 1 and 2) of this AD. Prior to further flight, correct any discrepancy detected, in accordance with the procedures described in the Boeing 747 Airplane Maintenance Manual. Repeat the functional test thereafter at intervals not to exceed 4,000 hours time-in-service. Alternative Methods of Compliance (g) An alternative method of compliance or adjustment of the compliance time that provides an acceptable level of safety may be used if approved by the Manager, Seattle Aircraft Certification Office (ACO), FAA, Transport Airplane Directorate. Operators shall submit their requests through an appropriate FAA Principal Maintenance Inspector, who may add comments and then send it to the Manager, Seattle ACO. Note 2: Information concerning the existence of approved alternative methods of compliance with this AD, if any, may be obtained from the Seattle ACO. Special Flight Permit (h) Special flight permits may be issued in accordance with sections 21.197 and 21.199 of the Federal Aviation Regulations (14 CFR 21.197 and 21.199) to operate the airplane to a location where the requirements of this AD can be accomplished. Incorporation by Reference (i) Except as provided by paragraph (f) of this AD, the actions shall be done in accordance with Boeing Service Bulletin 747-78A2149, Revision 1, dated May 9, 1996; Boeing Service Bulletin 747-78A2149, Revision 2, dated August 29, 1996; Boeing Alert Service Bulletin 747-78A2159, dated May 18, 1995; Boeing Service Bulletin 747-78-2135, dated August 31, 1995; Boeing Service Bulletin 747-78-2153, Revision 1, dated November 27, 1996; Rohr Service Bulletin TBC-CNS 78-32, Revision 1, dated August 20, 1996; and Rohr Service Bulletin TBC-CNS 78-33, Revision 1, dated August 20, 1996; as applicable. Rohr Service Bulletin TBC-CNS 78-32, Revision 1, dated August 20, 1996 contains the following list of effective pages:   Page No. Revision level shown on page Date shown on page 1, 3, 5-8, 10-11, 13-14, 16-18 1 August 20, 1996. 2, 4, 9, 12, 15 Original May 25, 1995. Rohr Service Bulletin TBC-CNS 78-33, Revision 1, dated August 20, 1996 contains the following list of effective pages:   Page No. Revision level shown on page Date shown on page 1, 3-55 1 August 20, 1996. 2 Original December 11, 1995. This incorporation by reference was approved by the Director of the Federal Register in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. Copies may be obtained from Boeing Commercial Airplane Group, P.O. Box 3707, Seattle, Washington 98124-2207. Copies may be inspected at the FAA, Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton, Washington; or at the Office of the Federal Register, 800 North Capitol Street, NW., suite 700, Washington, DC. (j) This amendment becomes effective on June 30, 2000. Appendix 1 Thrust Reverser Sync-Lock Integrity Test 1. General A. Equipment and Materials (1) Thrust reverser flex drive adapter—196K8004-1 or 196K8004-3; Rohr Industries, Inc., Chula Vista, California 92012. 2. Thrust Reverser Sync-Lock Integrity Test B. Prepare for the thrust reverser sync lock test. (1) Open applicable T/R CONT & BLEED SYS circuit breaker on P12 circuit breaker panel. (2) Open fan cowl doors (Ref 71-11-02, Maintenance Practices). (3) Check that forward and aft circumferential latches and all tension latches are engaged and locked. (4) Depress drive unit latch operating arm and retain by engaging latch arm (detail C). (5) Disengage stow latch hook on left and right thrust reversers (detail D). (6) On either lower slave actuator (detail B), either remove coverplate from forward drive pad or remove locking plug from lower drive pad. (7) Move left-hand sync-lock lever to the unlocked position. (8) Using appropriate drive adapter (196K8004-1 at forward drive pad or 196K8004-3 at lower drive pad), attempt to manually deploy sleeves. CAUTION: DO NOT APPLY A TORQUE LOAD OF MORE THAN 75 POUND-INCHES TO THE ACTUATOR; A GREATER TORQUE LOAD CAN CAUSE DAMAGE TO THE MECHANISM. (9) If sleeves move, replace the right-hand sync-lock. (10) Move left-hand sync-lock lever to the locked position. (11) Move right-hand sync-lock lever to the unlocked position. (12) Repeat step (8) above. (13) If sleeves move, replace the left-hand sync-lock. (14) Move left-hand sync-lock lever to the unlocked position. (15) Rotate actuator gearshaft to fully stow the sleeves. (16) When translating sleeves reach stowed position, check that stow latch hooks have engaged fixed hooks on both sides (detail D). (17) Depress latch operating arm and disengage latch arm (detail C); allow latch arm to raise. (18) After releasing arm, verify latch engagement by attempting to rotate feedback gear on drive unit using 1/4 -inch square drive; gear shall not rotate in excess of 0.1 of a turn. CAUTION: DO NOT APPLY A TORQUE LOAD OF MORE THAN 25 POUND-INCHES ON FEEDBACK GEAR; A GREATER TORQUE LOAD CAN CAUSE DAMAGE TO THE MECHANISM. (19) As applicable, install locking plug (with square section facing away from drive pad) or coverplate on actuator drive pad. Secure plug or plate with bolts tightened to 50-70 pound-inches. (20) Move both left-and right-hand sync-lock levers to the locked position. (21) Close fan cowl doors (Ref 71-11-02, Maintenance Practices). (22) Close T/R CONT & BLEED SYS circuit breaker. (23) Repeat the sync-lock integrity test on all remaining thrust reversers. BILLING CODE 4910-13-U ER26MY00.035 ER26MY00.036 Issued in Renton, Washington, on May 16, 2000. Donald L. Riggin, Acting Manager, Transport Airplane Directorate, Aircraft Certification Service. [FR Doc. 00-12812 Filed 5-25-00; 8:45 am] BILLING CODE 4910-13-C