AD 2001-23-51 Airworthiness Directives; Airbus Model A300 B4-600, B4-600R, and F4-600R (Collectively Called A300-600) Series Airplanes; and Model A310 Series Airplanes

Models named: A310 series. Read the applicability below — it usually turns on serial or part numbers too.

Model A300 B4-600, B4-600R, and F4-600R (collectively called A300-600) series airplanes; and Model A310 series airplanes; certificated in any category; having a vertical stabilizer made of composite material (reference Airbus Modification 4886). Note 1: This AD applies to each airplane identified in the preceding applicability provision, regardless of whether it has been modified, altered, or repaired in the area subject to the requirements of this AD. For airplanes that have been modified, altered, or repaired so that the performance of the requirements of this AD is affected, the owner/operator must request approval for an alternative method of compliance in accordance with paragraph (e) of this AD. The request should include an assessment of the effect of the modification, alteration, or repair on the unsafe condition addressed by this AD; and, if the unsafe condition has not been eliminated, the request should include specific proposed actions to address it.

Required as indicated, unless accomplished within the last 6 months. To prevent failure of the vertical stabilizer-to-fuselage attachment fittings or transverse (side) load fittings, or rudder-to-vertical stabilizer attachment fittings, which could result in loss of the vertical stabilizer and/or rudder and consequent loss of control of the airplane, accomplish the following: Compliance Time (a) Within 15 days after the effective date of this AD, do the inspections specified in paragraphs (b) and (c) of this AD. Note 2: For the purposes of this AD, a detailed visual inspection is defined as: “An intensive visual examination of a specific structural area, system, installation, or assembly to detect damage, failure, or irregularity. Available lighting is normally supplemented with a direct source of good lighting at intensity deemed appropriate by the inspector. Inspection aids such as mirror, magnifying lenses, etc., may be used. Surface cleaning and elaborate access procedures may be required.” Inspection and Corrective Actions (b) Perform a one-time detailed visual inspection to detect repairs and alterations to, and damage of the vertical stabilizer attachment fittings, including the main attachment lugs and the transverse (side) load fittings. Any alteration made to the composite structures, either during production or post-production, is considered areas of primary concern. Gain access to the vertical stabilizer attachment fittings by removing external fairings and internal access covers and inspect both sides of affected attachment fittings. Damage of the metallic areas includes pulled or loose fasteners, wear areas, distorted flanges, cracks, and corrosion. Damage of the composite areas includes delamination; distorted surfaces that may indicate delamination; cracks or abrading in the paint surface; surface damage; evidence of moisture damage; and cracked, splitting, or frayed fibers. (1) If any damage is found to the vertical stabilizer attachment fittings, including the main attachment lugs and the transverse (side) load fittings, before further flight, repair per a method approved by the Manager, International Branch, ANM-116, FAA, Transport Airplane Directorate. (2) If any repair or alteration to the attachment lug areas of the vertical stabilizer has been accomplished previously, before further flight, the repair or alteration must be approved by the Manager, International Branch, ANM-116. (c) Perform a one-time detailed visual inspection to detect damage of the rudder hinge fittings, hinge arms, and support fittings for all rudder hinges, and rudder actuator support fittings. Damage of the metallic areas includes pulled or loose fasteners, wear areas, distorted flanges, cracks, and corrosion. Damage of the composite areas includes delamination; distorted surfaces that may indicate delamination; cracks or abrading in the paint surface; surface damage; evidence of moisture damage; and cracked, splitting, or frayed fibers. If any damage is found, before further flight, repair per the manufacturer's structural repair manual, or per a method approved by the Manager, International Branch, ANM-116. Report (d) Submit a report of inspection findings (both positive and negative) to the Manager, International Branch, ANM-116; fax (425) 227-1149; at the applicable time specified in paragraph (d)(1) or (d)(2) of this AD. The report must include the inspection results, a description of any repair, alteration, or discrepancy found, including digital photographs of the damaged area, the airplane serial number, and the number of flight cycles and flight hours on the airplane. Information collection requirements contained in this AD have been approved by the Office of Management and Budget (OMB) under the provisions of the Paperwork Reduction Act of 1980 (44 U.S.C. 3501 et seq. ) and have been assigned OMB Control Number 2120-0056. (1) For airplanes on which the inspection is accomplished after the effective date of this AD: Submit the report within 5 days after performing the inspection required by paragraph (a) of this AD. (2) For airplanes on which the inspection has been accomplished prior to the effective date of this AD: Submit the report within 5 days after the effective date of this AD. Alternative Methods of Compliance (e) An alternative method of compliance or adjustment of the compliance time that provides an acceptable level of safety may be used if approved by the Manager, International Branch, ANM-116. Operators shall submit their requests through an appropriate FAA Principal Maintenance Inspector, who may add comments and then send it to the Manager, International Branch, ANM-116. Note 3: Information concerning the existence of approved alternative methods of compliance with this AD, if any, may be obtained from the International Branch, ANM-116. Special Flight Permits (f) Special flight permits may be issued in accordance with sections 21.197 and 21.199 of the Federal Aviation Regulations (14 CFR 21.197 and 21.199) to operate the airplane to a location where the requirements of this AD can be accomplished. Effective Date (g) This amendment becomes effective on December 10, 2001, to all persons except those persons to whom it was made immediately effective by emergency AD 2001-23-51, issued on November 16, 2001, which contained the requirements of this amendment. Issued in Renton, Washington, on November 26, 2001. Vi L. Lipski, Manager, Transport Airplane Directorate, Aircraft Certification Service. [FR Doc. 01-30082 Filed 12-4-01; 8:45 am] BILLING CODE 4910-13-U