AD 2005-15-05 Airworthiness Directives; Airbus Model A300 B4-600, B4-600R, and F4-600R Series Airplanes, and Model A300 C4-605R Variant F Airplanes (Collectively Called A300-600 Series Airplanes)

Models named: A300 B4-601, B4-603, B4-620, B4-622, B4-605R, B4-622R, F4-605R, F4-622R, C4-605R Variant F. Read the applicability below — it usually turns on serial or part numbers too.

This AD applies to Airbus Model A300 B4-601, B4-603, B4-620, B4-622, B4-605R, B4-622R, F4-605R, F4-622R, and C4-605R Variant F airplanes; certificated in any category; having serial numbers 0812, 0813, 0815 through 0818 inclusive, 0821 through 0828 inclusive, and 0836 through 0838 inclusive.

You are responsible for having the actions required by this AD performed within the compliance times specified, unless the actions have already been done. Inspection and Related Investigative/Corrective Actions (f) Within 2,500 flight hours after the effective date of this AD: Do a one-time detailed inspection for evidence of chafing between the hydraulic flexible hose and the RAT hub, and any applicable related investigative and corrective actions, by accomplishing all of the applicable actions specified in the Accomplishment Instructions of Airbus Service Bulletin A300-29-6054, Revision 01, excluding Appendix 01, dated November 4, 2004. Any applicable corrective actions must be accomplished before further flight. Although the service bulletin specifies to submit certain information to the manufacturer, and to submit damaged RATs to the vendor or a repair station, this AD does not include those requirements. Note 1: For the purposes of this AD, a detailed inspection is: “An intensive examination of a specific item, installation, or assembly to detect damage, failure, or irregularity. Available lighting is normally supplemented with a direct source of good lighting at an intensity deemed appropriate. Inspection aids such as mirror, magnifying lenses, etc., may be necessary. Surface cleaning and elaborate procedures may be required.” Actions Accomplished Previously (g) Actions accomplished before the effective date of this AD, in accordance with the Accomplishment Instructions of Airbus Service Bulletin A300-29-6054, excluding Appendix 01, dated June 8, 2004, are acceptable for compliance with the corresponding actions specified in this AD. Alternative Methods of Compliance (AMOCs) (h) The Manager, International Branch, ANM-116, Transport Airplane Directorate, FAA, has the authority to approve AMOCs for this AD, if requested in accordance with the procedures found in 14 CFR 39.19. Related Information (i) French airworthiness directive F-2004-133, dated August 4, 2004, also addresses the subject of this AD. Material Incorporated by Reference (j) You must use Airbus Service Bulletin A300-29-6054, Revision 01, excluding Appendix 01, dated November 4, 2004, to perform the actions that are required by this AD, unless the AD specifies otherwise. The Director of the Federal Register approves the incorporation by reference of this document in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. To get copies of the service information, contact Airbus, 1 Rond Point Maurice Bellonte, 31707 Blagnac Cedex, France. To view the AD docket, go to the Docket Management Facility, U.S. Department of Transportation, 400 Seventh Street SW., room PL-401, Nassif Building, Washington, DC. To review copies of the service information, go to the National Archives and Records Administration (NARA). For information on the availability of this material at the NARA, call (202) 741-6030, or go to http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html. Issued in Renton, Washington, on July 11, 2005. Ali Bahrami, Manager, Transport Airplane Directorate, Aircraft Certification Service. [FR Doc. 05-14173 Filed 7-21-05; 8:45 am] BILLING CODE 4910-13-P

This AD was prompted by reports of holes in the ram air turbine (RAT) hub. We are issuing this AD to prevent a hole in the RAT hub cover. A hole in the RAT hub cover could allow water to enter the RAT governing mechanism, freeze during flight, and jam the governing mechanism. In addition, the metal particles that result from chafing between the hydraulic flexible hose and the RAT could mix with the lubricant grease and degrade the governing mechanism. In an emergency, a jammed or degraded RAT could result in failure of RAT deployment, loss of hydraulic pressure or electrical power to the airplane, and consequent reduced controllability of the airplane.