AD 2006-02-11 Airworthiness Directives; McDonnell Douglas Model DC-10-10, DC-10-10F, DC-10-15, DC-10-30, DC-10-30F (KC-10A and KDC-10), DC-10-40, DC-10-40F, MD-10-10F, MD-10-30F, MD-11, and MD-11F Airplanes

This AD applies to all McDonnell Douglas Model DC-10-10, DC-10-10F, DC-10-15, DC-10-30, DC-10-30F (KC-10A and KDC-10), DC-10-40, DC-10-40F, MD-10-10F, MD-10-30F, MD-11, and MD-11F airplanes; certificated in any category.

You are responsible for having the actions required by this AD performed within the compliance times specified, unless the actions have already been done. Repetitive Inspections (f) Within 90 days after the effective date of this AD, do a detailed inspection for accumulation of debris (blockage) in the drain holes of the pitot tubes in accordance with paragraph (g) of this AD. Repeat the inspection thereafter at intervals not to exceed 1,000 flight hours. Note 1: For the purposes of this AD, a detailed inspection is “an intensive examination of a specific item, installation, or assembly to detect damage, failure, or irregularity. Available lighting is normally supplemented with a direct source of good lighting at an intensity deemed appropriate. Inspection aids such as mirrors magnifying lenses, etc. may be necessary. Surface cleaning and elaborate procedures may be required.” Visual Check (g) Do a visual check in accordance with paragraphs (g)(1) through (g)(3) of this AD. The visual check must be done by certificated maintenance personnel. (1) Make certain that the pitot heat is off and the pitot tubes are not hot. Note 2: Caution. Exercise care in checking pitot tubes to prevent severe burns to your hands. (2) Attempt to look through the left and right drain holes of each pitot tube. (3) Make sure that ambient light (or flashlight) is visible through both drain holes of each pitot tube. Corrective Action (h) If any evidence of drain hole blockage is found during any inspection required by paragraph (f) or (g) of this AD, before further flight, clean the hole in accordance with a method approved by the Manager, Los Angeles Aircraft Certification Office (ACO), FAA. Chapter 34-11-02 of the Boeing DC-10 or MD-10 Airplane Maintenance Manual is one approved method for Model DC-10-10, DC-10-10F, DC-10-15, DC-10-30, DC-10-30F (KC-10A and KDC-10), DC-10-40, DC-10-40F, MD-10-10F, and MD-10-30F airplanes; as applicable. Chapter 34-11-01 of the applicable Boeing MD-11 Airplane Maintenance Manual is one approved method for Model MD-11 and MD-11F airplanes. Alternative Methods of Compliance (AMOCs) (i)(1) The Manager, Los Angeles ACO, FAA, has the authority to approve AMOCs for this AD, if requested in accordance with the procedures found in 14 CFR 39.19. (2) Before using any AMOC approved in accordance with § 39.19 on any airplane to which the AMOC applies, notify the appropriate principal inspector in the FAA Flight Standards Certificate Holding District Office. Material Incorporated by Reference (j) None. Issued in Renton, Washington, on January 19, 2006. Ali Bahrami, Manager, Transport Airplane Directorate, Aircraft Certification Service. [FR Doc. 06-734 Filed 1-26-06; 8:45 am] BILLING CODE 4910-13-P

This AD was prompted by reports of blocked drain holes of the pitot tubes. We are issuing this AD to prevent blocked drain holes of the pitot tubes, which could result in the accumulation of water in the pitot-static system and consequent failure of that system. Failure of the pitot-static system could result in erroneous airspeed indications in the cockpit and consequent loss of airspeed control.