AD 2007-04-13 Airworthiness Directives; EADS SOCATA Model TBM 700 Airplanes

Makes named: socata. Models named: TBM 700. Read the applicability below — it usually turns on serial or part numbers too.

This AD applies to Model TBM 700 airplanes, serial numbers 1 through 9999, certificated in any category. Reason (d) The mandatory continuing airworthiness information (MCAI) states reports of cracks found on several main landing gear (MLG) cylinders. If not detected and corrected, fatigue cracks in the shock strut cylinder of the MLG could result in a collapsed MLG during takeoff or landing, and possible reduced structural integrity of the airplane.

Unless already done, do the following actions. (1) As of March 23, 2007 (the effective date of this AD), for MLG with forging body totaling more than 1,750 landings but less than 3,501 landings since new: (i) Inspect the forging body for cracks within 100 landings after March 23, 2007 (the effective date of this AD) in accordance with the accomplishment instructions of EADS SOCATA TBM Aircraft Mandatory Service Bulletin SB 70-130, ATA No. 32, dated January 2006. (ii) If no cracks are detected, repetitively inspect thereafter every 175 landings. (2) As of March 23, 2007 (the effective date of this AD), for MLG with forging body totaling more than 3,500 landings since new: (i) Inspect the forging body for cracks within 25 landings after March 23, 2007 (the effective date of this AD) in accordance with the accomplishment instructions of EADS SOCATA TBM Aircraft Mandatory Service Bulletin SB 70-130, ATA No. 32, dated January 2006. (ii) If no cracks are detected, repetitively inspect thereafter every 175 landings. (3) If any cracks are detected during any inspection required in paragraph (e) of this AD: (i) Before further flight, remove the affected landing gear leg and confirm the presence of the crack with dye penetrant inspection or fluorescent penetrant inspection. (ii) If the crack is confirmed, before further flight, contact EADS SOCATA to coordinate the landing gear repair/replacement and then conform to any instruction stated by EADS SOCATA. (4) If you do not know the number of landings, follow the instructions in the Compliance section of EADS SOCATA TBM Aircraft Mandatory Service Bulletin SB 70-130, ATA No. 32, dated January 2006. FAA AD Differences Note: This AD differs from the MCAI and/or service information as follows: No differences. Other FAA AD Provisions (f) The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, Standards Staff, FAA, Small Airplane Directorate, ATTN: Albert J. Mercado, Aerospace Engineer, 901 Locust, Room 301, Kansas City, Missouri 64106; telephone: (816) 329-4119; fax: (816) 329-4090, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. (2) Airworthy Product: For any requirement in this AD to obtain corrective actions from a manufacturer or other source, use these actions if they are FAA-approved. Corrective actions are considered FAA-approved if they are approved by the State of Design Authority (or their delegated agent). You are required to assure the product is airworthy before it is returned to service. (3) Reporting Requirements: For any reporting requirement in this AD, under the provisions of the Paperwork Reduction Act (44 U.S.C. 3501 et seq. ), the Office of Management and Budget (OMB) has approved the information collection requirements and has assigned OMB Control Number 2120-0056. Related Information (g) Refer to MCAI European Aviation Safety Agency (EASA) AD No. 2006-0085, dated April 12, 2006, for related information. Material Incorporated by Reference (h) You must use EADS SOCATA TBM Aircraft Mandatory Service Bulletin SB 70-130, ATA No. 32, dated January 2006, to do the actions required by this AD, unless the AD specifies otherwise. (1) The Director of the Federal Register approved the incorporation by reference of this service information under 5 U.S.C. 552(a) and 1 CFR part 51. (2) For service information identified in this AD, contact EADS SOCATA, Direction des Services, 65921 Tarbes Cedex 9, France; telephone: 33 (0)5 62.41.73.00; fax: 33 (0)5 62.41.76.54. (3) You may review copies at the FAA, Central Region, Office of the Regional Counsel, 901 Locust, Room 506, Kansas City, Missouri 64106; or at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202-741-6030, or go to: http://www.archives.gov/federal-register/cfr/ibr-locations.html. Issued in Kansas City, Missouri, on February 8, 2007. Kim Smith, Manager, Small Airplane Directorate, Aircraft Certification Service. [FR Doc. 07-670 Filed 2-15-07; 8:45 am] BILLING CODE 4910-13-P

Unless already done, do the following actions. (1) As of March 23, 2007 (the effective date of this AD), for MLG with forging body totaling more than 1,750 landings but less than 3,501 landings since new: (i) Inspect the forging body for cracks within 100 landings after March 23, 2007 (the effective date of this AD) in accordance with the accomplishment instructions of EADS SOCATA TBM Aircraft Mandatory Service Bulletin SB 70-130, ATA No. 32, dated January 2006. (ii) If no cracks are detected, repetitively inspect thereafter every 175 landings. (2) As of March 23, 2007 (the effective date of this AD), for MLG with forging body totaling more than 3,500 landings since new: (i) Inspect the forging body for cracks within 25 landings after March 23, 2007 (the effective date of this AD) in accordance with the accomplishment instructions of EADS SOCATA TBM Aircraft Mandatory Service Bulletin SB 70-130, ATA No. 32, dated January 2006. (ii) If no cracks are detected, repetitively inspect thereafter every 175 landings. (3) If any cracks are detected during any inspection required in paragraph (e) of this AD: (i) Before further flight, remove the affected landing gear leg and confirm the presence of the crack with dye penetrant inspection or fluorescent penetrant inspection. (ii) If the crack is confirmed, before further flight, contact EADS SOCATA to coordinate the landing gear repair/replacement and then conform to any instruction stated by EADS SOCATA. (4) If you do not know the number of landings, follow the instructions in the Compliance section of EADS SOCATA TBM Aircraft Mandatory Service Bulletin SB 70-130, ATA No. 32, dated January 2006. FAA AD Differences Note: This AD differs from the MCAI and/or service information as follows: No differences. Other FAA AD Provisions (f) The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, Standards Staff, FAA, Small Airplane Directorate, ATTN: Albert J. Mercado, Aerospace Engineer, 901 Locust, Room 301, Kansas City, Missouri 64106; telephone: (816) 329-4119; fax: (816) 329-4090, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. (2) Airworthy Product: For any requirement in this AD to obtain corrective actions from a manufacturer or other source, use these actions if they are FAA-approved. Corrective actions are considered FAA-approved if they are approved by the State of Design Authority (or their delegated agent). You are required to assure the product is airworthy before it is returned to service. (3) Reporting Requirements: For any reporting requirement in this AD, under the provisions of the Paperwork Reduction Act (44 U.S.C. 3501 et seq. ), the Office of Management and Budget (OMB) has approved the information collection requirements and has assigned OMB Control Number 2120-0056. Related Information (g) Refer to MCAI European Aviation Safety Agency (EASA) AD No. 2006-0085, dated April 12, 2006, for related information. Material Incorporated by Reference (h) You must use EADS SOCATA TBM Aircraft Mandatory Service Bulletin SB 70-130, ATA No. 32, dated January 2006, to do the actions required by this AD, unless the AD specifies otherwise. (1) The Director of the Federal Register approved the incorporation by reference of this service information under 5 U.S.C. 552(a) and 1 CFR part 51. (2) For service information identified in this AD, contact EADS SOCATA, Direction des Services, 65921 Tarbes Cedex 9, France; telephone: 33 (0)5 62.41.73.00; fax: 33 (0)5 62.41.76.54. (3) You may review copies at the FAA, Central Region, Office of the Regional Counsel, 901 Locust, Room 506, Kansas City, Missouri 64106; or at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202-741-6030, or go to: http://www.archives.gov/federal-register/cfr/ibr-locations.html. Issued in Kansas City, Missouri, on February 8, 2007. Kim Smith, Manager, Small Airplane Directorate, Aircraft Certification Service. [FR Doc. 07-670 Filed 2-15-07; 8:45 am] BILLING CODE 4910-13-P