Airworthiness directives › 2007-09-02
AD 2007-09-02 Airworthiness Directives; REIMS AVIATION S.A. Model F406 Airplanes
Models named: F406. Read the applicability below — it usually turns on serial or part numbers too.
Applicability*9
This AD applies to REIMS AVIATION S.A. Model F406 airplanes, serial numbers F406-0001 through F406-0089 and serial number F406-0091, certificated in any category.
Compliance
Unless already done, do the following actions: (1) Within the next 600 hours time-in-service or the next 12 months after the effective date of this AD, whichever occurs first, and thereafter repetitively during a period not to exceed 12 months, inspect the ribs in accordance with REIMS AVIATION INDUSTRIES Service Bulletin No. F406-54 REV 1, dated November 9, 2004. (2) If cracks are found during any inspection required by this AD, before further flight, do the actions prescribed in chapters 1D and 2E of the REIMS AVIATION INDUSTRIES Service Bulletin No. F406-54 REV 1, dated November 9, 2004. Note 1: We have established the repetitive inspection times of this AD so that they may coincide with annual inspections. FAA AD Differences Note 2: This AD differs from the MCAI and/or service information as follows: No differences. Other FAA AD Provisions (g) The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, Standards Staff, FAA, ATTN: Mike Kiesov, Aerospace Engineer, FAA, Small Airplane Directorate, 901 Locust, Room 301, Kansas City, Missouri 64106; telephone: (816) 329-4144; fax: (816) 329-4090, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. (2) Airworthy Product: For any requirement in this AD to obtain corrective actions from a manufacturer or other source, use these actions if they are FAA-approved. Corrective actions are considered FAA-approved if they are approved by the State of Design Authority (or their delegated agent). You are required to assure the product is airworthy before it is returned to service. (3) Reporting Requirements: For any reporting requirement in this AD, under the provisions of the Paperwork Reduction Act (44 U.S.C. 3501 et seq. ), the Office of Management and Budget (OMB) has approved the information collection requirements and has assigned OMB Control Number 2120-0056. Related Information (h) Refer to MCAI Direction générale de l'aviation civile (DGAC), which is the aviation authority for France, AD No. F-2004-114 R1, dated January 5, 2005; and REIMS AVIATION INDUSTRIES Service Bulletin No. F406-54 REV 1, dated November 9, 2004, for related information. Material Incorporated by Reference You must use REIMS AVIATION INDUSTRIES Service Bulletin No. F406-54 REV 1, dated November 9, 2004, to do the actions required by this AD, unless the AD specifies otherwise. (1) The Director of the Federal Register approved the incorporation by reference of this service information under 5 U.S.C. 552(a) and 1 CFR part 51. (2) For service information identified in this AD, contact REIMS AVIATION INDUSTRIES, 51360 PRUNAY-FRANCE. (3) You may review copies at the FAA, Central Region, Office of the Regional Counsel, 901 Locust, Room 506, Kansas City, Missouri 64106; or at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202-741-6030, or go to: http://www.archives.gov/federal-register/cfr/ibr-locations.html . Issued in Kansas City, Missouri, on April 13, 2007. Charles L. Smalley, Acting Manager, Small Airplane Directorate, Aircraft Certification Service. [FR Doc. E7-7641 Filed 4-25-07; 8:45 am] BILLING CODE 4910-13-P
Required actions
Unless already done, do the following actions: (1) Within the next 600 hours time-in-service or the next 12 months after the effective date of this AD, whichever occurs first, and thereafter repetitively during a period not to exceed 12 months, inspect the ribs in accordance with REIMS AVIATION INDUSTRIES Service Bulletin No. F406-54 REV 1, dated November 9, 2004. (2) If cracks are found during any inspection required by this AD, before further flight, do the actions prescribed in chapters 1D and 2E of the REIMS AVIATION INDUSTRIES Service Bulletin No. F406-54 REV 1, dated November 9, 2004. Note 1: We have established the repetitive inspection times of this AD so that they may coincide with annual inspections. FAA AD Differences Note 2: This AD differs from the MCAI and/or service information as follows: No differences. Other FAA AD Provisions (g) The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, Standards Staff, FAA, ATTN: Mike Kiesov, Aerospace Engineer, FAA, Small Airplane Directorate, 901 Locust, Room 301, Kansas City, Missouri 64106; telephone: (816) 329-4144; fax: (816) 329-4090, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. (2) Airworthy Product: For any requirement in this AD to obtain corrective actions from a manufacturer or other source, use these actions if they are FAA-approved. Corrective actions are considered FAA-approved if they are approved by the State of Design Authority (or their delegated agent). You are required to assure the product is airworthy before it is returned to service. (3) Reporting Requirements: For any reporting requirement in this AD, under the provisions of the Paperwork Reduction Act (44 U.S.C. 3501 et seq. ), the Office of Management and Budget (OMB) has approved the information collection requirements and has assigned OMB Control Number 2120-0056. Related Information (h) Refer to MCAI Direction générale de l'aviation civile (DGAC), which is the aviation authority for France, AD No. F-2004-114 R1, dated January 5, 2005; and REIMS AVIATION INDUSTRIES Service Bulletin No. F406-54 REV 1, dated November 9, 2004, for related information. Material Incorporated by Reference You must use REIMS AVIATION INDUSTRIES Service Bulletin No. F406-54 REV 1, dated November 9, 2004, to do the actions required by this AD, unless the AD specifies otherwise. (1) The Director of the Federal Register approved the incorporation by reference of this service information under 5 U.S.C. 552(a) and 1 CFR part 51. (2) For service information identified in this AD, contact REIMS AVIATION INDUSTRIES, 51360 PRUNAY-FRANCE. (3) You may review copies at the FAA, Central Region, Office of the Regional Counsel, 901 Locust, Room 506, Kansas City, Missouri 64106; or at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202-741-6030, or go to: http://www.archives.gov/federal-register/cfr/ibr-locations.html . Issued in Kansas City, Missouri, on April 13, 2007. Charles L. Smalley, Acting Manager, Small Airplane Directorate, Aircraft Certification Service. [FR Doc. E7-7641 Filed 4-25-07; 8:45 am] BILLING CODE 4910-13-P
Read the original on the Federal Register →
You just looked this one up by hand
TrackAD holds all 12,278 of them and matches them against the aircraft you actually look after — airframe, engine, propeller and appliances in one pass — then works out what falls due and when.
- Bring your existing list in from a spreadsheet Paste the rows straight out of Excel. Headers like C/W Date and N/A are read for you.
- A copy that works when this does not One file. No internet, no login, no this software running. For the morning something has to be produced and the computer is not cooperating.
- $5 a month, or $50 a year Up to 50 aircraft on either.
Look round a real shop first Start free
The demonstration shop is eleven real aircraft with a year of work behind them. No account needed.
The directive text above is reproduced from the Federal Register, a work of the United States government and in the public domain. The separation into applicability, compliance and required actions is TrackAD's.*1