AD 2007-17-20 Airworthiness Directives; Pacific Aerospace Limited Model 750XL Airplanes

Makes named: pacific aerospace. Read the applicability below — it usually turns on serial or part numbers too.

This AD applies to 750XL airplanes, serial numbers 101, 102, 104 through 120, and 122 through 129, certificated in any category.

Unless already done, within the next 6 months after October 2, 2007 (the effective date of this AD) or within the next 150 hours time-in-service after October 2, 2007 (the effective date of this AD), whichever occurs first, rework the left and right ailerons in accordance with Pacific Aerospace Ltd drawing number 11-03141/42, drawn March 26, 2007, as specified in Pacific Aerospace Limited Mandatory Service Bulletin PACSB/XL/027, dated March 27, 2007. FAA AD Differences Note: This AD differs from the MCAI and/or service information as follows: No differences. Other FAA AD Provisions (g) The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, Standards Staff, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. Send information to ATTN: Karl Schletzbaum, Aerospace Engineer, FAA, Small Airplane Directorate, 901 Locust, Room 301, Kansas City, Missouri 64106; telephone: (816) 329-4146; fax: (816) 329-4090. Before using any approved AMOC on any airplane to which the AMOC applies, notify your appropriate principal inspector (PI) in the FAA Flight Standards District Office (FSDO), or lacking a PI, your local FSDO. (2) Airworthy Product: For any requirement in this AD to obtain corrective actions from a manufacturer or other source, use these actions if they are FAA approved. Corrective actions are considered FAA approved if they are approved by the State of Design Authority (or their delegated agent). You are required to assure the product is airworthy before it is returned to service. (3) Reporting Requirements: For any reporting requirement in this AD, under the provisions of the Paperwork Reduction Act (44 U.S.C. 3501 et. seq.), the Office of Management and Budget (OMB) has approved the information collection requirements and has assigned OMB Control Number 2120-0056. Related Information (h) Refer to MCAI Civil Aviation Authority of New Zealand AD DCA/750XL/13, effective date April 26, 2007; Pacific Aerospace Limited Mandatory Service Bulletin PACSB/XL/027, dated March 27, 2007; and Pacific Aerospace Ltd drawing number 11-03141/42, drawn March 26, 2007, for related information. Material Incorporated by Reference (i) You must use Pacific Aerospace Limited Mandatory Service Bulletin PACSB/XL/027, dated March 27, 2007; and Pacific Aerospace Ltd drawing number 11-03141/42, drawn March 26, 2007, to do the actions required by this AD, unless the AD specifies otherwise. (1) The Director of the Federal Register approved the incorporation by reference of this service information under 5 U.S.C. 552(a) and 1 CFR part 51. (2) For service information identified in this AD, contact Pacific Aerospace Limited, Private Bag HN3027, Hamilton, New Zealand, telephone: +(64) 7-843-6144, fax: +(64) 7-843-6134, e-mail: pacific@aerospace.co.nz. (3) You may review copies at the FAA, Central Region, Office of the Regional Counsel, 901 Locust, Room 506, Kansas City, Missouri 64106; or at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202-741-6030, or go to: http://www.archives.gov/federal-register/cfr/ibr-locations.html. Issued in Kansas City, Missouri, on August 16, 2007. Terry L. Chasteen, Acting Manager, Small Airplane Directorate, Aircraft Certification Service. [FR Doc. E7-16652 Filed 8-27-07; 8:45 am] BILLING CODE 4910-13-P

Unless already done, within the next 6 months after October 2, 2007 (the effective date of this AD) or within the next 150 hours time-in-service after October 2, 2007 (the effective date of this AD), whichever occurs first, rework the left and right ailerons in accordance with Pacific Aerospace Ltd drawing number 11-03141/42, drawn March 26, 2007, as specified in Pacific Aerospace Limited Mandatory Service Bulletin PACSB/XL/027, dated March 27, 2007. FAA AD Differences Note: This AD differs from the MCAI and/or service information as follows: No differences. Other FAA AD Provisions (g) The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, Standards Staff, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. Send information to ATTN: Karl Schletzbaum, Aerospace Engineer, FAA, Small Airplane Directorate, 901 Locust, Room 301, Kansas City, Missouri 64106; telephone: (816) 329-4146; fax: (816) 329-4090. Before using any approved AMOC on any airplane to which the AMOC applies, notify your appropriate principal inspector (PI) in the FAA Flight Standards District Office (FSDO), or lacking a PI, your local FSDO. (2) Airworthy Product: For any requirement in this AD to obtain corrective actions from a manufacturer or other source, use these actions if they are FAA approved. Corrective actions are considered FAA approved if they are approved by the State of Design Authority (or their delegated agent). You are required to assure the product is airworthy before it is returned to service. (3) Reporting Requirements: For any reporting requirement in this AD, under the provisions of the Paperwork Reduction Act (44 U.S.C. 3501 et. seq.), the Office of Management and Budget (OMB) has approved the information collection requirements and has assigned OMB Control Number 2120-0056. Related Information (h) Refer to MCAI Civil Aviation Authority of New Zealand AD DCA/750XL/13, effective date April 26, 2007; Pacific Aerospace Limited Mandatory Service Bulletin PACSB/XL/027, dated March 27, 2007; and Pacific Aerospace Ltd drawing number 11-03141/42, drawn March 26, 2007, for related information. Material Incorporated by Reference (i) You must use Pacific Aerospace Limited Mandatory Service Bulletin PACSB/XL/027, dated March 27, 2007; and Pacific Aerospace Ltd drawing number 11-03141/42, drawn March 26, 2007, to do the actions required by this AD, unless the AD specifies otherwise. (1) The Director of the Federal Register approved the incorporation by reference of this service information under 5 U.S.C. 552(a) and 1 CFR part 51. (2) For service information identified in this AD, contact Pacific Aerospace Limited, Private Bag HN3027, Hamilton, New Zealand, telephone: +(64) 7-843-6144, fax: +(64) 7-843-6134, e-mail: pacific@aerospace.co.nz. (3) You may review copies at the FAA, Central Region, Office of the Regional Counsel, 901 Locust, Room 506, Kansas City, Missouri 64106; or at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202-741-6030, or go to: http://www.archives.gov/federal-register/cfr/ibr-locations.html. Issued in Kansas City, Missouri, on August 16, 2007. Terry L. Chasteen, Acting Manager, Small Airplane Directorate, Aircraft Certification Service. [FR Doc. E7-16652 Filed 8-27-07; 8:45 am] BILLING CODE 4910-13-P