AD 2008-06-16 Airworthiness Directives; Pacific Aerospace Corporation, Ltd Model 750XL Airplanes

Makes named: pacific aerospace. Models named: 750XL. Read the applicability below — it usually turns on serial or part numbers too.

This AD applies to Model 750XL airplanes, serial numbers 102 through 134, certificated in any category. Note 1: The applicability of this AD takes precedence over Pacific Aerospace Corporation Limited Mandatory Service Bulletin PACSB/XL/009, issue 2, revised July 23, 2004.

Unless already done, do the following actions: (1) Within the next 100 hours time-in-service (TIS) after April 23, 2008 (the effective date of this AD), inspect the main wiring loom on the right hand side of the aircraft adjacent to the frames at station 114.34” and 118.84” to ensure there are two pieces of protective sleeving installed following Pacific Aerospace Corporation Limited Mandatory Service Bulletin PACSB/XL/009, issue 2, revised July 23, 2004. (2) If you find the protective sleeves are missing as a result of the inspection required by paragraph (f)(1) of this AD, before further flight, install protective sleeves following Pacific Aerospace Corporation Mandatory Service Bulletin PACSB/XL/009, issue 2, revised July 23, 2004. FAA AD Differences Note 2: This AD differs from the MCAI and/or service information as follows: No differences. Other FAA AD Provisions (g) The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, Standards Office, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. Send information to ATTN: Karl Schletzbaum, Aerospace Engineer, FAA, Small Airplane Directorate, 901 Locust, Room 301, Kansas City, Missouri 64106; telephone: (816) 329-4146; fax: (816) 329-4090. Before using any approved AMOC on any airplane to which the AMOC applies, notify your appropriate principal inspector (PI) in the FAA Flight Standards District Office (FSDO), or lacking a PI, your local FSDO. Material Incorporated by Reference (h) You must use Pacific Aerospace Corporation Limited Mandatory Service Bulletin PACSB/XL/009, issue 2, revised July 23, 2004, to do the actions required by this AD, unless the AD specifies otherwise. (1) The Director of the Federal Register approved the incorporation by reference of this service information under 5 U.S.C. 552(a) and 1 CFR part 51. (2) For service information identified in this AD, contact Pacific Aerospace Limited, Hamilton Airport, Private Bag, 3027 Hamilton, New Zealand; telephone: +64 7-843-6144; facsimile: +64 7-843-6134. (3) You may review copies at the FAA, Central Region, Office of the Regional Counsel, 901 Locust, Room 506, Kansas City, Missouri 64106; or at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202-741-6030, or go to: http://www.archives.gov/federal-register/cfr/ibr-locations.html . Issued in Kansas City, Missouri, on March 7, 2008. Kim Smith, Manager, Small Airplane Directorate, Aircraft Certification Service. [FR Doc. E8-5062 Filed 3-18-08; 8:45 am] BILLING CODE 4910-13-P

Unless already done, do the following actions: (1) Within the next 100 hours time-in-service (TIS) after April 23, 2008 (the effective date of this AD), inspect the main wiring loom on the right hand side of the aircraft adjacent to the frames at station 114.34” and 118.84” to ensure there are two pieces of protective sleeving installed following Pacific Aerospace Corporation Limited Mandatory Service Bulletin PACSB/XL/009, issue 2, revised July 23, 2004. (2) If you find the protective sleeves are missing as a result of the inspection required by paragraph (f)(1) of this AD, before further flight, install protective sleeves following Pacific Aerospace Corporation Mandatory Service Bulletin PACSB/XL/009, issue 2, revised July 23, 2004. FAA AD Differences Note 2: This AD differs from the MCAI and/or service information as follows: No differences. Other FAA AD Provisions (g) The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, Standards Office, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. Send information to ATTN: Karl Schletzbaum, Aerospace Engineer, FAA, Small Airplane Directorate, 901 Locust, Room 301, Kansas City, Missouri 64106; telephone: (816) 329-4146; fax: (816) 329-4090. Before using any approved AMOC on any airplane to which the AMOC applies, notify your appropriate principal inspector (PI) in the FAA Flight Standards District Office (FSDO), or lacking a PI, your local FSDO. Material Incorporated by Reference (h) You must use Pacific Aerospace Corporation Limited Mandatory Service Bulletin PACSB/XL/009, issue 2, revised July 23, 2004, to do the actions required by this AD, unless the AD specifies otherwise. (1) The Director of the Federal Register approved the incorporation by reference of this service information under 5 U.S.C. 552(a) and 1 CFR part 51. (2) For service information identified in this AD, contact Pacific Aerospace Limited, Hamilton Airport, Private Bag, 3027 Hamilton, New Zealand; telephone: +64 7-843-6144; facsimile: +64 7-843-6134. (3) You may review copies at the FAA, Central Region, Office of the Regional Counsel, 901 Locust, Room 506, Kansas City, Missouri 64106; or at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202-741-6030, or go to: http://www.archives.gov/federal-register/cfr/ibr-locations.html . Issued in Kansas City, Missouri, on March 7, 2008. Kim Smith, Manager, Small Airplane Directorate, Aircraft Certification Service. [FR Doc. E8-5062 Filed 3-18-08; 8:45 am] BILLING CODE 4910-13-P