AD 2008-12-14 Airworthiness Directives; Dassault Model Falcon 2000EX Airplanes

Models named: Falcon 2000EX. Read the applicability below — it usually turns on serial or part numbers too.

This AD applies to Dassault Model Falcon 2000EX airplanes; certificated in any category; having serial numbers 1 through 5 and 7 through 27 inclusive.

Within 6 months after the effective date of this AD, unless already done, modify the electrical wiring of the wings' anti-ice system, in accordance with the Accomplishment Instructions of Dassault Service Bulletin F2000EX-116, dated May 31, 2006; and Service Bulletin F2000EX-140, dated February 28, 2007. FAA AD Differences Note: This AD differs from the MCAI and/or service information as follows: No differences. Other FAA AD Provisions (g) The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, International Branch, ANM-116, Transport Airplane Directorate, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. Send information to ATTN: Tom Rodriguez, Aerospace Engineer, International Branch, ANM-116, Transport Airplane Directorate, FAA, 1601 Lind Avenue, SW., Renton, Washington 98057-3356; telephone (425) 227-1137; fax (425) 227-1149. Before using any approved AMOC on any airplane to which the AMOC applies, notify your appropriate principal inspector (PI) in the FAA Flight Standards District Office (FSDO), or lacking a PI, your local FSDO. (2) Airworthy Product: For any requirement in this AD to obtain corrective actions from a manufacturer or other source, use these actions if they are FAA-approved. Corrective actions are considered FAA-approved if they are approved by the State of Design Authority (or their delegated agent). You are required to assure the product is airworthy before it is returned to service. (3) Reporting Requirements: For any reporting requirement in this AD, under the provisions of the Paperwork Reduction Act, the Office of Management and Budget (OMB) has approved the information collection requirements and has assigned OMB Control Number 2120-0056. Related Information (h) Refer to MCAI European Aviation Safety Agency (EASA) Airworthiness Directive 2007-0137, dated May 16, 2007; Dassault Service Bulletin F2000EX-116, dated May 31, 2006; and Dassault Service Bulletin F2000EX-140, dated February 28, 2007 for related information. Material Incorporated by Reference (i) You must use Dassault Service Bulletin F2000EX-116, dated May 31, 2006 and Dassault Service Bulletin F2000EX-140, dated February 28, 2007, as applicable, to do the actions required by this AD, unless the AD specifies otherwise. Dassault Service Bulletin F2000EX-140, dated February 28, 2007, contains the following effective pages:   Page No. Shown on page 1-4, 6-8 February 28, 2007. 5 June 14, 2007. (1) The Director of the Federal Register approved the incorporation by reference of this service information under 5 U.S.C. 552(a) and 1 CFR part 51. (2) For service information identified in this AD, contact Dassault Falcon Jet, P.O. Box 2000, South Hackensack, New Jersey 07606. (3) You may review copies at the FAA, Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton, Washington; or at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call (202) 741-6030, or go to: http://www.archives.gov/federal-register/cfr/ibr-locations.html. Issued in Renton, Washington, on June 3, 2008. Michael Kaszycki, Acting Manager, Transport Airplane Directorate, Aircraft Certification Service. [FR Doc. E8-13320 Filed 6-17-08; 8:45 am] BILLING CODE 4910-13-P

Within 6 months after the effective date of this AD, unless already done, modify the electrical wiring of the wings' anti-ice system, in accordance with the Accomplishment Instructions of Dassault Service Bulletin F2000EX-116, dated May 31, 2006; and Service Bulletin F2000EX-140, dated February 28, 2007. FAA AD Differences Note: This AD differs from the MCAI and/or service information as follows: No differences. Other FAA AD Provisions (g) The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, International Branch, ANM-116, Transport Airplane Directorate, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. Send information to ATTN: Tom Rodriguez, Aerospace Engineer, International Branch, ANM-116, Transport Airplane Directorate, FAA, 1601 Lind Avenue, SW., Renton, Washington 98057-3356; telephone (425) 227-1137; fax (425) 227-1149. Before using any approved AMOC on any airplane to which the AMOC applies, notify your appropriate principal inspector (PI) in the FAA Flight Standards District Office (FSDO), or lacking a PI, your local FSDO. (2) Airworthy Product: For any requirement in this AD to obtain corrective actions from a manufacturer or other source, use these actions if they are FAA-approved. Corrective actions are considered FAA-approved if they are approved by the State of Design Authority (or their delegated agent). You are required to assure the product is airworthy before it is returned to service. (3) Reporting Requirements: For any reporting requirement in this AD, under the provisions of the Paperwork Reduction Act, the Office of Management and Budget (OMB) has approved the information collection requirements and has assigned OMB Control Number 2120-0056. Related Information (h) Refer to MCAI European Aviation Safety Agency (EASA) Airworthiness Directive 2007-0137, dated May 16, 2007; Dassault Service Bulletin F2000EX-116, dated May 31, 2006; and Dassault Service Bulletin F2000EX-140, dated February 28, 2007 for related information. Material Incorporated by Reference (i) You must use Dassault Service Bulletin F2000EX-116, dated May 31, 2006 and Dassault Service Bulletin F2000EX-140, dated February 28, 2007, as applicable, to do the actions required by this AD, unless the AD specifies otherwise. Dassault Service Bulletin F2000EX-140, dated February 28, 2007, contains the following effective pages:   Page No. Shown on page 1-4, 6-8 February 28, 2007. 5 June 14, 2007. (1) The Director of the Federal Register approved the incorporation by reference of this service information under 5 U.S.C. 552(a) and 1 CFR part 51. (2) For service information identified in this AD, contact Dassault Falcon Jet, P.O. Box 2000, South Hackensack, New Jersey 07606. (3) You may review copies at the FAA, Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton, Washington; or at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call (202) 741-6030, or go to: http://www.archives.gov/federal-register/cfr/ibr-locations.html. Issued in Renton, Washington, on June 3, 2008. Michael Kaszycki, Acting Manager, Transport Airplane Directorate, Aircraft Certification Service. [FR Doc. E8-13320 Filed 6-17-08; 8:45 am] BILLING CODE 4910-13-P