AD 2008-13-04 Airworthiness Directives; Dassault Model Mystere-Falcon 20-C5, 20-D5, and 20-E5 Airplanes

Models named: Mystere-Falcon 20-C5, 20-D5, 20-E5. Read the applicability below — it usually turns on serial or part numbers too.

This AD applies to Dassault Model Mystere-Falcon 20-C5, 20-D5, and 20-E5 airplanes, certificated in any category, all serial numbers.

Within 7 months after the effective date of this AD, unless already done, do the following actions. (1) Inspect to determine whether any wing anti-ice flexible hose having part number (P/N) FAL1006 or P/N ARM224A is installed. A review of airplane maintenance records is acceptable in lieu of this inspection if the part number of the wing anti-ice flexible hose can be conclusively determined from that review. If any wing anti-ice flexible hose does not have P/N FAL1006 or P/N ARM224A, no further action is required by this AD for that hose, except as required by paragraph (f)(3) of this AD. (2) Remove any wing anti-ice flexible hose having P/N FAL1006 or P/N ARM224A, and install a new hose having ESPA (brand) P/N 60503104509; in accordance with the Accomplishment Instructions of Dassault Service Bulletin F20-775, dated July 9, 2007. (3) As of the effective date of this AD, no person shall install any flexible hose having P/N FAL1006 or P/N ARM224A on any Model Mystere-Falcon 20-C5, 20-D5, or 20-E5 airplane specified in the applicability of this AD. FAA AD Differences Note 1: This AD differs from the MCAI and/or service information as follows: The MCAI does not require inspecting to determine the part numbers of the wing anti-ice flexible hoses. This AD requires such an inspection. Other FAA AD Provisions (g) The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, International Branch, ANM-116, Transport Airplane Directorate, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. Send information to ATTN: Tom Rodriguez, Aerospace Engineer, International Branch, ANM-116, Transport Airplane Directorate, FAA, 1601 Lind Avenue, SW., Renton, Washington 98057-3356; telephone (425) 227-1137; fax (425) 227-1149. Before using any approved AMOC on any airplane to which the AMOC applies, notify your appropriate principal inspector (PI) in the FAA Flight Standards District Office (FSDO), or lacking a PI, your local FSDO. (2) Airworthy Product: For any requirement in this AD to obtain corrective actions from a manufacturer or other source, use these actions if they are FAA-approved. Corrective actions are considered FAA-approved if they are approved by the State of Design Authority (or their delegated agent). You are required to assure the product is airworthy before it is returned to service. (3) Reporting Requirements: For any reporting requirement in this AD, under the provisions of the Paperwork Reduction Act, the Office of Management and Budget (OMB) has approved the information collection requirements and has assigned OMB Control Number 2120-0056. Related Information (h) Refer to MCAI European Aviation Safety Agency Airworthiness Directive 2007-0227, dated September 17, 2007; and Dassault Service Bulletin F20-775, dated July 9, 2007; for related information. Material Incorporated by Reference (i) You must use Dassault Service Bulletin F20-775, dated July 9, 2007, to do the actions required by this AD, unless the AD specifies otherwise. (1) The Director of the Federal Register approved the incorporation by reference of this service information under 5 U.S.C. 552(a) and 1 CFR part 51. (2) For service information identified in this AD, contact Dassault Falcon Jet, P.O. Box 2000, South Hackensack, New Jersey 07606. (3) You may review copies at the FAA, Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton, Washington; or at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call (202) 741-6030, or go to: http://www.archives.gov/federal-register/cfr/ibr-locations.html. Issued in Renton, Washington, on June 9, 2008. Ali Bahrami, Manager, Transport Airplane Directorate, Aircraft Certification Service. [FR Doc. E8-13576 Filed 6-18-08; 8:45 am] BILLING CODE 4910-13-P

Within 7 months after the effective date of this AD, unless already done, do the following actions. (1) Inspect to determine whether any wing anti-ice flexible hose having part number (P/N) FAL1006 or P/N ARM224A is installed. A review of airplane maintenance records is acceptable in lieu of this inspection if the part number of the wing anti-ice flexible hose can be conclusively determined from that review. If any wing anti-ice flexible hose does not have P/N FAL1006 or P/N ARM224A, no further action is required by this AD for that hose, except as required by paragraph (f)(3) of this AD. (2) Remove any wing anti-ice flexible hose having P/N FAL1006 or P/N ARM224A, and install a new hose having ESPA (brand) P/N 60503104509; in accordance with the Accomplishment Instructions of Dassault Service Bulletin F20-775, dated July 9, 2007. (3) As of the effective date of this AD, no person shall install any flexible hose having P/N FAL1006 or P/N ARM224A on any Model Mystere-Falcon 20-C5, 20-D5, or 20-E5 airplane specified in the applicability of this AD. FAA AD Differences Note 1: This AD differs from the MCAI and/or service information as follows: The MCAI does not require inspecting to determine the part numbers of the wing anti-ice flexible hoses. This AD requires such an inspection. Other FAA AD Provisions (g) The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, International Branch, ANM-116, Transport Airplane Directorate, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. Send information to ATTN: Tom Rodriguez, Aerospace Engineer, International Branch, ANM-116, Transport Airplane Directorate, FAA, 1601 Lind Avenue, SW., Renton, Washington 98057-3356; telephone (425) 227-1137; fax (425) 227-1149. Before using any approved AMOC on any airplane to which the AMOC applies, notify your appropriate principal inspector (PI) in the FAA Flight Standards District Office (FSDO), or lacking a PI, your local FSDO. (2) Airworthy Product: For any requirement in this AD to obtain corrective actions from a manufacturer or other source, use these actions if they are FAA-approved. Corrective actions are considered FAA-approved if they are approved by the State of Design Authority (or their delegated agent). You are required to assure the product is airworthy before it is returned to service. (3) Reporting Requirements: For any reporting requirement in this AD, under the provisions of the Paperwork Reduction Act, the Office of Management and Budget (OMB) has approved the information collection requirements and has assigned OMB Control Number 2120-0056. Related Information (h) Refer to MCAI European Aviation Safety Agency Airworthiness Directive 2007-0227, dated September 17, 2007; and Dassault Service Bulletin F20-775, dated July 9, 2007; for related information. Material Incorporated by Reference (i) You must use Dassault Service Bulletin F20-775, dated July 9, 2007, to do the actions required by this AD, unless the AD specifies otherwise. (1) The Director of the Federal Register approved the incorporation by reference of this service information under 5 U.S.C. 552(a) and 1 CFR part 51. (2) For service information identified in this AD, contact Dassault Falcon Jet, P.O. Box 2000, South Hackensack, New Jersey 07606. (3) You may review copies at the FAA, Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton, Washington; or at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call (202) 741-6030, or go to: http://www.archives.gov/federal-register/cfr/ibr-locations.html. Issued in Renton, Washington, on June 9, 2008. Ali Bahrami, Manager, Transport Airplane Directorate, Aircraft Certification Service. [FR Doc. E8-13576 Filed 6-18-08; 8:45 am] BILLING CODE 4910-13-P