AD 2008-16-13 Airworthiness Directives; Boeing Model 737-600, -700, -700C, -800, -900, and -900ER Series Airplanes

Models named: 737-600, -700, -700C, -800, -900, -900ER series. Read the applicability below — it usually turns on serial or part numbers too.

This AD applies to Boeing Model 737-600, -700, -700C, -800, -900, and -900ER series airplanes, certificated in any category; line numbers 1 through 2196 inclusive.

Comply with this AD within the compliance times specified, unless already done. Pushrod Replacement (f) At the time specified in paragraph 1.E., “Compliance,” of Boeing Special Attention Service Bulletin 737-27-1284, dated November 28, 2007; except, where the service bulletin specifies a compliance time after the date on the service bulletin, this AD requires compliance within the specified compliance time after the effective date of this AD: Replace the pushrods for the left and right elevator tab control mechanisms with new, improved pushrods by doing all the actions in accordance with the Accomplishment Instructions of Boeing Special Attention Service Bulletin 737-27-1284, dated November 28, 2007. Parts Installation (g) As of the effective date of this AD, no person may install a pushrod assembly, part number 65-45166-24, on any airplane. Alternative Methods of Compliance (AMOCs) (h)(1) The Manager, Seattle Aircraft Certification Office (ACO), FAA, ATTN: Tamara Anderson, Aerospace Engineer, Airframe Branch, ANM-120S, FAA, Seattle ACO, 1601 Lind Avenue, SW., Renton, Washington 98057-3356; telephone (425) 917-6421; fax (425) 917-6590; has the authority to approve AMOCs for this AD, if requested, using the procedures found in 14 CFR 39.19. (2) To request a different method of compliance or a different compliance time for this AD, follow the procedures in 14 CFR 39.19. Before using any approved AMOC on any airplane to which the AMOC applies, notify your appropriate principal inspector (PI) in the FAA Flight Standards District Office (FSDO), or lacking a PI, your local FSDO. (3) An AMOC that provides an acceptable level of safety may be used for any repair required by this AD, if it is approved by an Authorized Representative for the Boeing Commercial Airplanes Delegation Option Authorization Organization who has been authorized by the Manager, Seattle ACO, to make those findings. For a repair method to be approved, the repair must meet the certification basis of the airplane. Material Incorporated by Reference (i) You must use Boeing Special Attention Service Bulletin 737-27-1284, dated November 28, 2007, to do the actions required by this AD, unless the AD specifies otherwise. (1) The Director of the Federal Register approved the incorporation by reference of this service information under 5 U.S.C. 552(a) and 1 CFR part 51. (2) For service information identified in this AD, contact Boeing Commercial Airplanes, P.O. Box 3707, Seattle, Washington 98124-2207. (3) You may review copies of the service information incorporated by reference at the FAA, Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton, Washington; or at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202-741-6030, or go to: http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html . Issued in Renton, Washington, on July 23, 2008. Ali Bahrami, Manager, Transport Airplane Directorate, Aircraft Certification Service. [FR Doc. E8-17748 Filed 8-4-08; 8:45 am] BILLING CODE 4910-13-P

This AD results from a report of a rod end fracture on a rudder power control unit (PCU) control rod, which is similar to the ones used for the elevator tab pushrods. Analysis revealed that the fractured rod end had an incorrect hardness, which had probably occurred during the manufacture of the control rod. We are issuing this AD to prevent fracture of the elevator tab pushrod ends, which could result in excessive in-flight vibrations of the elevator tab, possible loss of the elevator tab, and consequent loss of controllability of the airplane.