AD 2009-02-09 Airworthiness Directives; BAE Systems (Operations) Limited Model BAe 146 and Avro 146-RJ Airplanes

Models named: BAe 146-100A, -200A, -300A series, Avro 146-RJ70A, 146-RJ85A, 146-RJ100A. Read the applicability below — it usually turns on serial or part numbers too.

This AD applies to BAE Systems (Operations) Limited Model BAe 146-100A, -200A, and -300A series airplanes; and Model Avro 146-RJ70A, 146-RJ85A, and 146-RJ100A airplanes, certificated in any category, all models, all serial numbers.

Unless already done, do the following actions: Before accumulating 48 months on the wing link since new, or within 48 months of a wing link being repaired in accordance with a BAE Systems (Operations) Limited or European Aviation Safety Agency (EASA) approved repair scheme, or within 24 months after the effective date of this AD, whichever occurs latest, and thereafter at intervals not to exceed 48 months, inspect the wing links in accordance with paragraph 2.C. of BAE Systems (Operations) Limited Inspection Service Bulletin ISB.53-203, dated May 7, 2007 (“the service bulletin”). (1) If any corrosion is found on bolts or nuts, replace the affected bolts and nuts with airworthy parts before next flight in accordance with the service bulletin. (2) If any corrosion to the wing links is found during an inspection, repair before further flight in accordance with a method approved in accordance with EASA (or its delegated agent). FAA AD Differences Note 1: This AD differs from the MCAI and/or service information as follows: No differences. Other FAA AD Provisions (g) The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, International Branch, ANM-116, Transport Airplane Directorate, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. Send information to ATTN: Todd Thompson, Aerospace Engineer, International Branch, ANM-116, Transport Airplane Directorate, FAA, 1601 Lind Avenue, SW., Renton, Washington 98057-3356; telephone (425) 227-1175; fax (425) 227-1149. Before using any approved AMOC on any airplane to which the AMOC applies, notify your appropriate principal inspector (PI) in the FAA Flight Standards District Office (FSDO), or lacking a PI, your local FSDO. (2) Airworthy Product: For any requirement in this AD to obtain corrective actions from a manufacturer or other source, use these actions if they are FAA-approved. Corrective actions are considered FAA-approved if they are approved by the State of Design Authority (or their delegated agent). You are required to assure the product is airworthy before it is returned to service. (3) Reporting Requirements: For any reporting requirement in this AD, under the provisions of the Paperwork Reduction Act, the Office of Management and Budget (OMB) has approved the information collection requirements and has assigned OMB Control Number 2120-0056. Related Information (h) Refer to MCAI EASA Airworthiness Directive 2007-0303, dated December 14, 2007, and BAE Systems (Operations) Limited Inspection Service Bulletin ISB.53-203, dated May 7, 2007, for related information. Material Incorporated by Reference (i) You must use BAE Systems (Operations) Limited Inspection Service Bulletin ISB.53-203, dated May 7, 2007, to do the actions required by this AD, unless the AD specifies otherwise. (1) The Director of the Federal Register approved the incorporation by reference of this service information under 5 U.S.C. 552(a) and 1 CFR part 51. (2) For service information identified in this AD, contact BAE Systems Regional Aircraft, 13850 McLearen Road, Herndon, Virginia 20171; telephone 703-736-1080; e-mail raebusiness@baesystems.com; Internet http://www.baesystems.com/Businesses/RegionalAircraft/index.htm. (3) You may review copies of the service information that is incorporated by reference at the FAA, Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton, Washington. For information on the availability of this material at the FAA, call 425-227-1221 or 425-227-1152. (4) You may also review copies of the service information at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202-741-6030, or go to: http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html . Issued in Renton, Washington, on January 15, 2009. Ali Bahrami, Manager, Transport Airplane Directorate, Aircraft Certification Service. [FR Doc. E9-3366 Filed 2-25-09; 8:45 am] BILLING CODE 4910-13-P

Unless already done, do the following actions: Before accumulating 48 months on the wing link since new, or within 48 months of a wing link being repaired in accordance with a BAE Systems (Operations) Limited or European Aviation Safety Agency (EASA) approved repair scheme, or within 24 months after the effective date of this AD, whichever occurs latest, and thereafter at intervals not to exceed 48 months, inspect the wing links in accordance with paragraph 2.C. of BAE Systems (Operations) Limited Inspection Service Bulletin ISB.53-203, dated May 7, 2007 (“the service bulletin”). (1) If any corrosion is found on bolts or nuts, replace the affected bolts and nuts with airworthy parts before next flight in accordance with the service bulletin. (2) If any corrosion to the wing links is found during an inspection, repair before further flight in accordance with a method approved in accordance with EASA (or its delegated agent). FAA AD Differences Note 1: This AD differs from the MCAI and/or service information as follows: No differences. Other FAA AD Provisions (g) The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, International Branch, ANM-116, Transport Airplane Directorate, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. Send information to ATTN: Todd Thompson, Aerospace Engineer, International Branch, ANM-116, Transport Airplane Directorate, FAA, 1601 Lind Avenue, SW., Renton, Washington 98057-3356; telephone (425) 227-1175; fax (425) 227-1149. Before using any approved AMOC on any airplane to which the AMOC applies, notify your appropriate principal inspector (PI) in the FAA Flight Standards District Office (FSDO), or lacking a PI, your local FSDO. (2) Airworthy Product: For any requirement in this AD to obtain corrective actions from a manufacturer or other source, use these actions if they are FAA-approved. Corrective actions are considered FAA-approved if they are approved by the State of Design Authority (or their delegated agent). You are required to assure the product is airworthy before it is returned to service. (3) Reporting Requirements: For any reporting requirement in this AD, under the provisions of the Paperwork Reduction Act, the Office of Management and Budget (OMB) has approved the information collection requirements and has assigned OMB Control Number 2120-0056. Related Information (h) Refer to MCAI EASA Airworthiness Directive 2007-0303, dated December 14, 2007, and BAE Systems (Operations) Limited Inspection Service Bulletin ISB.53-203, dated May 7, 2007, for related information. Material Incorporated by Reference (i) You must use BAE Systems (Operations) Limited Inspection Service Bulletin ISB.53-203, dated May 7, 2007, to do the actions required by this AD, unless the AD specifies otherwise. (1) The Director of the Federal Register approved the incorporation by reference of this service information under 5 U.S.C. 552(a) and 1 CFR part 51. (2) For service information identified in this AD, contact BAE Systems Regional Aircraft, 13850 McLearen Road, Herndon, Virginia 20171; telephone 703-736-1080; e-mail raebusiness@baesystems.com; Internet http://www.baesystems.com/Businesses/RegionalAircraft/index.htm. (3) You may review copies of the service information that is incorporated by reference at the FAA, Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton, Washington. For information on the availability of this material at the FAA, call 425-227-1221 or 425-227-1152. (4) You may also review copies of the service information at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202-741-6030, or go to: http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html . Issued in Renton, Washington, on January 15, 2009. Ali Bahrami, Manager, Transport Airplane Directorate, Aircraft Certification Service. [FR Doc. E9-3366 Filed 2-25-09; 8:45 am] BILLING CODE 4910-13-P