AD 2009-12-10 Airworthiness Directives; BAE Systems (Operations) Limited Model BAe 146 and Avro 146-RJ Airplanes

Models named: BAe 146-100A, -200A, -300A series, Avro 146-RJ70A, 146-RJ85A, 146-RJ100A. Read the applicability below — it usually turns on serial or part numbers too.

This AD applies to all BAE Systems (Operations) Limited Model BAe 146-100A, -200A, and -300A series airplanes; and Model Avro 146-RJ70A, 146-RJ85A, and 146-RJ100A airplanes; certificated in any category.

You are responsible for having the actions required by this AD performed within the compliance times specified, unless the actions have already been done. Restatement of Requirements of AD 2006-12-09 Repetitive Inspections (g) Use high-frequency eddy current (HFEC) and detailed methods to inspect for signs of corrosion (including cracks, blistering, or flaking paint) of frames 15, 18, 41, and 43, in accordance with the Accomplishment Instructions of BAE Systems (Operations) Limited Inspection Service Bulletin ISB.53-182, dated March 16, 2005, except as required by paragraph (k) of this AD. Inspect at the applicable time specified in 1.D. “Compliance” of BAE Systems (Operations) Limited Inspection Service Bulletin ISB.53-182, dated March 16, 2005. Application of corrosion-preventive treatment, in accordance with BAE Systems (Operations) Limited Inspection Service Bulletin ISB.53-182, dated March 16, 2005; or Revision 1, dated August 6, 2007; extends the repetitive inspection interval, as specified in Table 2 in 1.D. “Compliance” of BAE Systems (Operations) Limited Inspection Service Bulletin ISB.53-182, dated March 16, 2005. Note 1: For the purposes of this AD, a detailed inspection is: “An intensive examination of a specific item, installation, or assembly to detect damage, failure, or irregularity. Available lighting is normally supplemented with a direct source of good lighting at an intensity deemed appropriate. Inspection aids such as mirror, magnifying lenses, etc., may be necessary. Surface cleaning and elaborate procedures may be required.” Corrective Action (h) If any discrepancy is found during any inspection required by paragraph (g) of this AD: Before further flight, perform applicable related investigative/corrective actions in accordance with the Accomplishment Instructions of BAE Systems (Operations) Limited Inspection Service Bulletin ISB.53-182, dated March 16, 2005, except as required by paragraphs (i) and (k) of this AD. Exceptions to Service Bulletin Specifications (i) If BAE Systems (Operations) Limited Inspection Service Bulletin ISB.53-182, dated March 16, 2005, specifies to contact the manufacturer for appropriate action, before further flight, repair per a method approved by the Manager, International Branch, ANM-116, Transport Airplane Directorate, FAA; or the Civil Aviation Authority (or its delegated agent); or European Aviation Safety Agency (EASA) (or its delegated agent). (j) Where BAE Systems (Operations) Limited Inspection Service Bulletin ISB.53-182, dated March 16, 2005, specifies a compliance time after the issuance of the service bulletin, this AD requires compliance within the specified compliance time after July 17, 2006 (the effective date of AD 2006-12-09). Where BAE Systems (Operations) Limited Inspection Service Bulletin ISB.53-182, dated March 16, 2005, specifies a compliance time “since date of construction” of the airplane, this AD requires compliance since the date of issuance of the original standard airworthiness certificate or the date of issuance of the original export certificate of airworthiness. New Requirements of This AD New Service Bulletin (k) As of the effective date of this AD: Do the actions required by paragraphs (g) and (h) of this AD in accordance with the Accomplishment Instructions of BAE Systems (Operations) Limited Inspection Service Bulletin ISB.53-182, Revision 1, dated August 6, 2007, except as required by paragraph (n) of this AD. Additional Inspection Areas (l) At the applicable compliance time specified in paragraph (g) of this AD, except as provided by paragraph (o) of this AD; or within six months after the effective date of this AD; whichever occurs later: Do an HFEC inspection for corrosion of the outer frame flanges and door hinge bosses of frames 15, 18, 41, and 43, in accordance with the Accomplishment Instructions of BAE Systems (Operations) Limited Inspection Service Bulletin ISB.53-182, Revision 1, dated August 6, 2007 (“the service bulletin”). Repeat the inspection thereafter at the applicable time specified in paragraph 1.D., “Compliance,” of the service bulletin. Application of corrosion-preventive treatment, in accordance with the Accomplishment Instructions of the service bulletin, extends the repetitive inspection interval, as specified in Table 2 in paragraph 1.D., “Compliance,” of the service bulletin. Corrective Action for Additional Inspection (m) If any discrepancy is found during any inspection required by paragraph (l) of this AD: Before further flight, perform applicable related investigative/corrective actions in accordance with the Accomplishment Instructions of BAE Systems (Operations) Limited Inspection Service Bulletin ISB.53-182, Revision 1, dated August 6, 2007, except as required by paragraph (n) of this AD. Exceptions to BAE Systems (Operations) Limited Inspection Service Bulletin ISB.53-182, Revision 1 (n) If BAE Systems (Operations) Limited Inspection Service Bulletin ISB.53-182, Revision 1, dated August 6, 2007, specifies to contact the manufacturer for appropriate action, before further flight, repair per a method approved by the Manager, International Branch, ANM-116, Transport Airplane Directorate, FAA; or EASA (or its delegated agent). (o) Where BAE Systems (Operations) Limited Inspection Service Bulletin ISB.53-182, Revision 1, dated August 6, 2007, specifies a compliance time after the issuance of the service bulletin, this AD requires compliance within the specified compliance time after the effective date of this AD. Where BAE Systems (Operations) Limited Inspection Service Bulletin ISB.53-182, Revision 1, dated August 6, 2007, specifies a compliance time “since date of construction” of the airplane, this AD requires compliance since the date of issuance of the original airworthiness certificate or the date of issuance of the original export certificate of airworthiness. No Reporting (p) Although BAE Systems (Operations) Limited Inspection Service Bulletin ISB.53-182, dated March 16, 2005; and Revision 1, dated August 6, 2007; specify to submit information to the manufacturer, this AD does not include such a requirement. Alternative Methods of Compliance (AMOCs) (q) The Manager, International Branch, ANM-116, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. Send information to ATTN: Todd Thompson, Aerospace Engineer, International Branch, ANM-116, Transport Airplane Directorate, FAA, 1601 Lind Avenue, SW., Renton, Washington 98057-3356; telephone (425) 227-1175; fax (425) 227-1149. Before using any approved AMOC on any airplane to which the AMOC applies, notify your principal maintenance inspector (PMI) or principal avionics inspector (PAI), as appropriate, or lacking a principal inspector, your local Flight Standards District Office. The AMOC approval letter must specifically reference this AD. Related Information (r) European Aviation Safety Agency Airworthiness Directive 2008-0092 R1, dated May 15, 2008, also addresses the subject of this AD. Material Incorporated by Reference (s) You must BAE Systems (Operations) Limited Inspection Service Bulletin ISB.53-182, Revision 1, dated August 6, 2007; as applicable; to do the actions required by this AD, unless the AD specifies otherwise. (1) The Director of the Federal Register approved the incorporation by reference of this service information under 5 U.S.C. 552(a) and 1 CFR part 51. (2) For service information identified in this AD, contact BAE Systems Regional Aircraft, 13850 McLearen Road, Herndon, Virginia 20171; telephone 703-736-1080; e-mail raebusiness@baesystems.com; Internet http://www.baesystems.com/Businesses/RegionalAircraft/index.htm. (3) You may review copies of the service information at the FAA, Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton, Washington. For information on the availability of this material at the FAA, call 425-227-1221 or 425-227-1152. (4) You may also review copies of the service information that is incorporated by reference at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202-741-6030, or go to: http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html . Issued in Renton, Washington, on June 2, 2009. Stephen P. Boyd, Acting Manager, Transport Airplane Directorate, Aircraft Certification Service. [FR Doc. E9-13567 Filed 6-18-09; 8:45 am] BILLING CODE 4910-13-P

This AD results from a report indicating that corrosion has been detected in the outer frame flanges and door hinge bosses during scheduled maintenance. We are issuing this AD to prevent reduced structural integrity of the airplane.