AD 2009-24-09 Airworthiness Directives; Airbus Model A330-200 and -300 Series Airplanes; and Model A340-200 and -300 Series Airplanes

This AD applies to all Airbus Model A330-201, −202, −203, −223, −243, −301, −302, −303, −321, −322, −323, −341, −342, and −343 series airplanes, all manufacturer serial numbers; and Model A340-211, −212, −213, −311, −312, and −313 series airplanes, all manufacturer serial numbers; certificated in any category.

You are responsible for having the actions required by this AD performed within the compliance times specified, unless the actions have already been done. Actions (g) Do the actions required by paragraphs (g)(1) through (g)(3) of this AD. (1) For airplanes that do not have Airbus Modification 54491 embodied in production, or Airbus Service Bulletin A330-29-3101 or Airbus Service Bulletin A340-29-4078 embodied in service: Within 100 flight cycles or 28 days after the effective date of this AD, whichever occurs first, inspect the check valves on the blue, green, and yellow hydraulic systems to identify their P/Ns, in accordance with the instructions of Airbus All Operators Telex (AOT) A330-29A3111, Revision 1, dated October 8, 2009 (for Model A330-200 and -300 series airplanes); or AOT A340-29A4086, Revision 1, dated October 8, 2009 (for Model A340-200 and −300 series airplanes). (i) If check valves having P/N CAR401 are installed on all three hydraulic systems, before further flight, do the actions specified in paragraph (g)(2)(i) of this AD. After accomplishing the actions required by paragraph (g)(2)(i) of this AD, do the actions specified in paragraphs (g)(2)(ii) and (g)(2)(iii) of this AD at the applicable compliance times specified in those paragraphs. (ii) If check valves having P/N CAR401 are not installed on all three hydraulic systems, no further action is required until any check valve having P/N CAR400 is replaced with a check valve having P/N CAR401. If any check valve having P/N CAR400 is replaced by a check valve having P/N CAR401, before further flight, do the inspection specified in paragraph (g)(1) of this AD to determine if all three hydraulic systems are equipped with check valve having P/N CAR401. (2) For airplanes on which Airbus Modification 54491 was embodied in production, or Airbus Service Bulletin A330-29-3101 or Airbus Service Bulletin A340-29-4078 was embodied in service, do the actions specified in paragraphs (g)(2)(i), (g)(2)(ii), and (g)(2)(iii) of this AD. (i) Except as required by paragraph (g)(1)(i) of this AD, at the applicable times specified in paragraphs (g)(2)(i)(A) and (g)(2)(i)(B) of this AD, as applicable: Do the inspection program (detailed inspection of the lock wire for presence and integrity, a detailed inspection for traces of seepage or black deposits, and an inspection for proper torque) on yellow and blue high pressure manifolds, install new lock wires, and do all applicable corrective actions, in accordance with the instructions of paragraph 4.1.1 of Airbus AOT A330-29A3111, Revision 1, dated October 8, 2009 (for Model A330-200 and −300 series airplanes); or AOT A340-29A4086, Revision 1, dated October 8, 2009 (for Model A340-200 and −300 series airplanes). Do all applicable corrective actions before further flight. (A) For airplanes on which Airbus Modification 54491 has been embodied in production: At the later of the times specified in paragraphs (g)(2)(i)(A)( 1 ) and (g)(2)(i)(A)( 2 ) of this AD. ( 1 ) Before the accumulation of 1,000 total flight cycles since first flight but no earlier than the accumulation of 700 total flight cycles since first flight. ( 2 ) Within 100 flight cycles or 28 days after the effective date of this AD, whichever occurs first. (B) For airplanes on which Airbus Service Bulletin A330-29-3101 or A340-29-4078 was embodied in service: At the later of the times specified in paragraphs (g)(2)(i)(B)( 1 ) and (g)(2)(i)(B)( 2 ) of this AD. ( 1 ) Within 1,000 flight cycles since the embodiment of Airbus Service Bulletin A330-29-3101 or A340-29-4078 but no earlier than 700 flight cycles after the embodiment of Airbus Service Bulletin A330-29-3101 or A340-29-4078. ( 2 ) Within 100 flight cycles or 28 days after the effective date of this AD, whichever occurs first. (ii) Within 900 flight hours after accomplishment of paragraph (g)(2)(i) of this AD, do the inspection program (detailed inspection of the lock wire for presence and integrity, a detailed inspection for traces of seepage or black deposits, and an inspection for proper torque) and install a new lock wire on the green high pressure manifold; and do an inspection (detailed inspection for traces of seepage or black deposits, and detailed inspection to determine alignment of the check valve and manifold) on the yellow and blue high pressure manifolds, and do all applicable corrective actions; in accordance with the instructions of paragraph 4.1.2 of Airbus AOT A330-29A3111, Revision 1, dated October 8, 2009 (for Model A330-200 and −300 series airplanes); or AOT A340-29A4086, Revision 1, dated October 8, 2009 (for Model A340-200 and −300 series airplanes). Do all applicable corrective actions before further flight. (iii) Within 900 flight hours after accomplishment of paragraph (g)(2)(ii) of this AD, and thereafter at intervals not to exceed 900 flight hours, do the inspection program (detailed inspection for traces of seepage or black deposits, and detailed inspection to determine alignment of the check valve and manifold) on the green, yellow, and blue high pressure manifolds, and do all applicable corrective actions, in accordance with the instructions of paragraph 4.1.3 of Airbus AOT A330-29A3111, Revision 1, dated October 8, 2009 (for Model A330-200 and −300 series airplanes); or AOT A340-29A4086, Revision 1, dated October 8, 2009 (for Model A340-200 and −300 series airplanes). Do all applicable corrective actions before further flight. (iv) Actions accomplished before the effective date of this AD, according to Airbus AOT A330-29A3111, dated September 2, 2009 (for Model A330-200 and −300 series airplanes); or AOT A340-29A4086, dated September 2, 2009 (for Model A340-200 and −300 series airplanes); are considered acceptable for compliance with the corresponding actions specified in paragraph (g)(2)(i) of this AD. (3) Within 10 days after accomplishment of the inspections specified in paragraphs (g)(1) and (g)(2) of this AD, or within 10 days after the effective date of this AD, whichever occurs later, report all inspection results to Airbus in accordance with Airbus AOT A330-29A3111, Revision 1, dated October 8, 2009 (for Model A330-200 and -300 series airplanes); or AOT A340-29A4086, Revision 1, dated October 8, 2009 (for Model A340-200 and -300 series airplanes). FAA AD Differences Note 1: This AD differs from the MCAI and/or service information as follows: No differences. Other FAA AD Provisions (h) The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, International Branch, ANM-116, Transport Airplane Directorate, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. Send information to ATTN: Vladimir Ulyanov, Aerospace Engineer, International Branch, ANM-116, Transport Airplane Directorate, FAA, 1601 Lind Avenue, SW., Renton, Washington 98057-3356; telephone (425) 227-1138; fax (425) 227-1149. Before using any approved AMOC on any airplane to which the AMOC applies, notify your principal maintenance inspector (PMI) or principal avionics inspector (PAI), as appropriate, or lacking a principal inspector, your local Flight Standards District Office. The AMOC approval letter must specifically reference this AD. (2) Airworthy Product: For any requirement in this AD to obtain corrective actions from a manufacturer or other source, use these actions if they are FAA-approved. Corrective actions are considered FAA-approved if they are approved by the State of Design Authority (or their delegated agent). You are required to assure the product is airworthy before it is returned to service. (3) Reporting Requirements: For any reporting requirement in this AD, under the provisions of the Paperwork Reduction Act (44 U.S.C. 3501 et seq. ), the Office of Management and Budget (OMB) has approved the information collection requirements and has assigned OMB Control Number 2120-0056. Related Information (i) Refer to MCAI European Aviation Safety Agency Emergency Airworthiness Directive 2009-0223-E, dated October 13, 2009; and Airbus AOTs A330-29A3111 and A340-29A4086, both Revision 1, both dated October 8, 2009; for related information. Material Incorporated by Reference (j) You must use Airbus All Operators Telex A330-29A3111, Revision 1, dated October 8, 2009; or Airbus All Operators Telex A340-29A4086, Revision 1, dated October 8, 2009; as applicable; to do the actions required by this AD, unless the AD specifies otherwise. (Only the first page of these documents contains the document number, revision level, and date; no other page of these documents contain this information.) (1) The Director of the Federal Register approved the incorporation by reference of this service information under 5 U.S.C. 552(a) and 1 CFR part 51. (2) For service information identified in this AD, contact Airbus SAS—Airworthiness Office—EAL, 1 Rond Point Maurice Bellonte, 31707 Blagnac Cedex, France; telephone +33 5 61 93 36 96; fax +33 5 61 93 45 80, e-mail airworthiness.A330-A340@airbus.com ; Internet http://www.airbus.com. (3) You may review copies of the service information at the FAA, Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton, Washington. For information on the availability of this material at the FAA, call 425-227-1221 or 425-227-1152. (4) You may also review copies of the service information that is incorporated by reference at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202-741-6030, or go to: http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html. Issued in Renton, Washington, on November 16, 2009. Stephen P. Boyd, Acting Manager, Transport Airplane Directorate, Aircraft Certification Service. [FR Doc. E9-28069 Filed 11-25-09; 8:45 am] BILLING CODE 4910-13-P