AD 2010-04-14 Airworthiness Directives; Augustair, Inc. Models 2150, 2150A, and 2180 Airplanes

Models named: MS-1-P These. Read the applicability below — it usually turns on serial or part numbers too.

This AD applies to the following airplane models and serial numbers that are certificated in any category:   Model Serial Numbers Note 2150 FP-1 through FP-10 and MS-1-P These aircraft were produced by Morrisey Aviation Inc. 2150A SFP-11, SP12 through SP-33, and SP-35 through SP-45 These aircraft were produced by Shinn Engineering Company, Santa Ana, California, under licensing agreement with Morrisey Aviation Inc. 2150A VAC-50 through VAC-52, and VAC-54-76 through VAC-189-85 These aircraft were produced by Varga Aircraft Corporation, Chandler, Arizona. 2180 VAC-68-77 through VAC-191-82 These aircraft were produced by Varga Aircraft Corporation, Chandler, Arizona.

To address this problem, you must do the following, unless already done: (1) Before further flight after March 24, 2010 (the effective date of this AD), visually inspect the vertical stabilizer front spar for cracks and other damage (loose fasteners, corrosion, scratches) following section 2, paragraph A, of Augustair Service Bulletin SB2009-1, Revision B, dated February 2, 2010. (2) At the applicable compliance time specified in paragraph (f)(2)(i) and (f)(2)(ii) of this AD, do a detailed inspection of the vertical stabilizer front spar for cracks and other damage, repair any damage found, and install a doubler to the vertical stabilizer front spar following section 2, paragraph B, of Augustair Service Bulletin SB2009-1, Revision B, dated February 2, 2010. (i) Before further flight after the inspection required in paragraph (f)(1) of this AD where cracks or other damage is found; or (ii) Within 10 hours time-in-service (TIS) after the inspection required in paragraph (f)(1) of this AD where no cracks or other damage was found. (3) Report the inspection results from paragraph (f)(2) of this AD within 30 days after the inspection or within 30 days after March 24, 2010 (the effective date of this AD), whichever occurs later. Send your report to ATTN: Hal Horsburgh, Aerospace Engineer, FAA, Atlanta Aircraft Certification Office (ACO), 1701 Columbia Avenue, College Park, Georgia 30337; fax: (404) 474-5606; e-mail: hal.horsburgh@faa.gov. The Office of Management and Budget (OMB) approved the information collection requirements contained in this regulation under the provisions of the Paperwork Reduction Act and assigned OMB Control Number 2120-0056. Include in your report the following information: (1) Aircraft model and serial number; (2) Aircraft hours TIS; (3) Answer whether any crack was found and, if so, the crack location and size; (4) Description of any previous modifications or repairs in the vertical stabilizer spar attachment area or if the airplane was modified with a different engine model or propeller model than originally installed on the airplane and hours TIS when the modification was done; (5) Corrective action taken; (6) Answer yes or no whether other damage was found; and if so, describe it; (7) Point of contact name and phone number; and (8) Clearly identify the AD No., Docket No., and Directorate Identifier of the AD action requiring the report. Alternative Methods of Compliance (AMOCs) (g) The Manager, Atlanta Aircraft Certification Office (ACO), FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. Send information to ATTN: Hal Horsburgh, Aerospace Engineer, FAA, Atlanta Aircraft Certification Office (ACO), 1701 Columbia Avenue, College Park, Georgia 30337; telephone: (404) 474-5553; fax: (404) 474-5606; e-mail: hal.horsburgh@faa.gov. Before using any approved AMOC on any airplane to which the AMOC applies, notify your appropriate principal inspector (PI) in the FAA Flight Standards District Office (FSDO), or lacking a PI, your local FSDO. Material Incorporated by Reference (h) You must use Augustair Service Bulletin SB2009-1, Revision B, dated February 2, 2010, to do the actions required by this AD, unless the AD specifies otherwise. (1) The Director of the Federal Register approved the incorporation by reference of this service information under 5 U.S.C. 552(a) and 1 CFR part 51. (2) For service information identified in this AD, contact Augustair, Inc., 1809 Hephzibah McBean Rd., Hephzibah, Georgia 30815; telephone: (706) 836-8610; fax: (706) 925-2847; Internet: http://VG21squadron.com; e-mail: lorenperry@aol.com. (3) You may review copies of the service information incorporated by reference for this AD at the FAA, Central Region, Office of the Regional Counsel, 901 Locust, Kansas City, Missouri 64106. For information on the availability of this material at the Central Region, call (816) 329-3768. (4) You may also review copies of the service information incorporated by reference for this AD at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call (202) 741-6030, or go to: http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html. Issued in Kansas City, Missouri, on February 11, 2010. Steven W. Thompson, Acting Manager, Small Airplane Directorate, Aircraft Certification Service. [FR Doc. 2010-3185 Filed 2-22-10; 8:45 am] BILLING CODE 4910-13-P

This AD is the result of six reports of Augustair, Inc. Models 2150A and 2180 airplanes with a cracked vertical stabilizer front spar. We are issuing this AD to detect and correct cracks in the vertical stabilizer front spar, which could result in separation of the vertical stabilizer from the airplane. This failure could lead to loss of control.