AD 2010-13-04 Airworthiness Directives; Bombardier, Inc. Model DHC-8-400 Series Airplanes

Models named: DHC-8-400, DHC-8-401, DHC-8-402 series. Read the applicability below — it usually turns on serial or part numbers too.

This AD applies to Bombardier, Inc. Model DHC-8-400, DHC-8-401, and DHC-8-402 series airplanes, certificated in any category; serial numbers 4001, 4003, 4004, 4006, and 4008 through 4238 inclusive.

Unless already done, do the following actions. (1) Within 2,000 flight hours after the effective date of this AD: Modify the NLG trailing arm by incorporating Bombardier Modification Summary 4-113599, in accordance with the Accomplishment Instructions of Bombardier Service Bulletin 84-32-65, Revision A, dated March 2, 2009. (2) Incorporating Bombardier Modification Summary 4-113599 in accordance with the Accomplishment Instructions of Bombardier Service Bulletin 84-32-65, dated December 17, 2008, is also acceptable for compliance with the requirements of paragraph (f)(1) of this AD if done before the effective date of this AD. FAA AD Differences Note 1: This AD differs from the MCAI and/or service information as follows: No differences. Other FAA AD Provisions (g) The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, New York Aircraft Certification Office, ANE-170, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. Send information to ATTN: Program Manager, Continuing Operational Safety, FAA, New York ACO, 1600 Stewart Avenue, Suite 410, Westbury, New York 11590; telephone 516-228-7300; fax 516-794-5531. Before using any approved AMOC on any airplane to which the AMOC applies, notify your principal maintenance inspector (PMI) or principal avionics inspector (PAI), as appropriate, or lacking a principal inspector, your local Flight Standards District Office. The AMOC approval letter must specifically reference this AD. (2) Airworthy Product: For any requirement in this AD to obtain corrective actions from a manufacturer or other source, use these actions if they are FAA-approved. Corrective actions are considered FAA-approved if they are approved by the State of Design Authority (or their delegated agent). You are required to assure the product is airworthy before it is returned to service. (3) Reporting Requirements: For any reporting requirement in this AD, under the provisions of the Paperwork Reduction Act (44 U.S.C. 3501 et seq. ), the Office of Management and Budget (OMB) has approved the information collection requirements and has assigned OMB Control Number 2120-0056. Related Information (h) Refer to MCAI Canadian Airworthiness Directive CF-2009-29, dated June 29, 2009; and Bombardier Service Bulletin 84-32-65, Revision A, dated March 2, 2009; for related information. Material Incorporated by Reference (i) You must use Bombardier Service Bulletin 84-32-65, Revision A, dated March 2, 2009, to do the actions required by this AD, unless the AD specifies otherwise. (1) The Director of the Federal Register approved the incorporation by reference of this service information under 5 U.S.C. 552(a) and 1 CFR part 51. (2) For service information identified in this AD, contact Bombardier, Inc., 400 Côte-Vertu Road West, Dorval, Québec H4S 1Y9, Canada; telephone 514-855-5000; fax 514-855-7401; e-mail thd.qseries@aero.bombardier.com; Internet http://www.bombardier.com . (3) You may review copies of the service information at the FAA, Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton, Washington. For information on the availability of this material at the FAA, call 425-227-1221. (4) You may also review copies of the service information that is incorporated by reference at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202-741-6030, or go to: http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html. Issued in Renton, Washington, on June 10, 2010. Jeffrey E. Duven, Acting Manager, Transport Airplane Directorate, Aircraft Certification Service. [FR Doc. 2010-14984 Filed 6-22-10; 8:45 am] BILLING CODE 4910-13-P

Unless already done, do the following actions. (1) Within 2,000 flight hours after the effective date of this AD: Modify the NLG trailing arm by incorporating Bombardier Modification Summary 4-113599, in accordance with the Accomplishment Instructions of Bombardier Service Bulletin 84-32-65, Revision A, dated March 2, 2009. (2) Incorporating Bombardier Modification Summary 4-113599 in accordance with the Accomplishment Instructions of Bombardier Service Bulletin 84-32-65, dated December 17, 2008, is also acceptable for compliance with the requirements of paragraph (f)(1) of this AD if done before the effective date of this AD. FAA AD Differences Note 1: This AD differs from the MCAI and/or service information as follows: No differences. Other FAA AD Provisions (g) The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, New York Aircraft Certification Office, ANE-170, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. Send information to ATTN: Program Manager, Continuing Operational Safety, FAA, New York ACO, 1600 Stewart Avenue, Suite 410, Westbury, New York 11590; telephone 516-228-7300; fax 516-794-5531. Before using any approved AMOC on any airplane to which the AMOC applies, notify your principal maintenance inspector (PMI) or principal avionics inspector (PAI), as appropriate, or lacking a principal inspector, your local Flight Standards District Office. The AMOC approval letter must specifically reference this AD. (2) Airworthy Product: For any requirement in this AD to obtain corrective actions from a manufacturer or other source, use these actions if they are FAA-approved. Corrective actions are considered FAA-approved if they are approved by the State of Design Authority (or their delegated agent). You are required to assure the product is airworthy before it is returned to service. (3) Reporting Requirements: For any reporting requirement in this AD, under the provisions of the Paperwork Reduction Act (44 U.S.C. 3501 et seq. ), the Office of Management and Budget (OMB) has approved the information collection requirements and has assigned OMB Control Number 2120-0056. Related Information (h) Refer to MCAI Canadian Airworthiness Directive CF-2009-29, dated June 29, 2009; and Bombardier Service Bulletin 84-32-65, Revision A, dated March 2, 2009; for related information. Material Incorporated by Reference (i) You must use Bombardier Service Bulletin 84-32-65, Revision A, dated March 2, 2009, to do the actions required by this AD, unless the AD specifies otherwise. (1) The Director of the Federal Register approved the incorporation by reference of this service information under 5 U.S.C. 552(a) and 1 CFR part 51. (2) For service information identified in this AD, contact Bombardier, Inc., 400 Côte-Vertu Road West, Dorval, Québec H4S 1Y9, Canada; telephone 514-855-5000; fax 514-855-7401; e-mail thd.qseries@aero.bombardier.com; Internet http://www.bombardier.com . (3) You may review copies of the service information at the FAA, Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton, Washington. For information on the availability of this material at the FAA, call 425-227-1221. (4) You may also review copies of the service information that is incorporated by reference at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202-741-6030, or go to: http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html. Issued in Renton, Washington, on June 10, 2010. Jeffrey E. Duven, Acting Manager, Transport Airplane Directorate, Aircraft Certification Service. [FR Doc. 2010-14984 Filed 6-22-10; 8:45 am] BILLING CODE 4910-13-P