AD 2010-14-17 Airworthiness Directives; The Boeing Company Model 747-100, 747-100B, 747-100B SUD, 747-200B, 747-200C, 747-200F, 747-300, 747-400, 747SR, and 747SP Series Airplanes

Models named: 747-100, 747-100B, 747-100B SUD, 747-200B, 747-200C, 747-200F, 747-300, 747-400, 747SR, 747SP series. Read the applicability below — it usually turns on serial or part numbers too.

This AD applies to The Boeing Company Model 747-100, 747-100B, 747-100B SUD, 747-200B, 747-200C, 747-200F, 747-300, 747-400, 747SR, and 747SP series airplanes, certificated in any category; as identified in Boeing Alert Service Bulletin 747-53A2750, dated August 27, 2009.

You are responsible for having the actions required by this AD performed within the compliance times specified, unless the actions have already been done. Repetitive Inspections of the Overwing Intercostal Web (g) Before the accumulation of 8,000 total flight cycles, or within 1,500 flight cycles after the effective date of this AD, whichever occurs later: Do a detailed inspection of the left-side and right-side STAs 1160, 1180, 1200, and 1220 overwing intercostal webs, and do all applicable related investigative and corrective actions, in accordance with the Accomplishment Instructions of Boeing Alert Service Bulletin 747-53A2750, dated August 27, 2009, except as required by paragraph (i) of this AD. Do all applicable related investigative and corrective actions before further flight. If no cracking is found during any detailed inspection, repeat the inspection thereafter at intervals not to exceed 3,000 flight cycles. (h) For any airplane with an overwing intercostal web replaced in accordance with Boeing Alert Service Bulletin 747-53A2750, dated August 27, 2009: Within 6,000 flight cycles after the web was replaced, do a detailed inspection of the replacement overwing intercostal web, and do all applicable related investigative and corrective actions, in accordance with the Accomplishment Instructions of Boeing Alert Service Bulletin 747-53A2750, dated August 27, 2009, except as required by paragraph (i) of this AD. Do all applicable related investigative and corrective actions before further flight. If no cracking is found during any detailed inspection, repeat the inspection thereafter at intervals not to exceed 3,000 flight cycles. Exception to Service Bulletin (i) If any cracking is found during any inspection required by this AD, and Boeing Alert Service Bulletin 747-53A2750, dated August 27, 2009, specifies contacting Boeing for appropriate action: Before further flight, repair the cracking using a method approved in accordance with the procedures provided in paragraph (j) of this AD. Alternative Methods of Compliance (AMOCs) (j)(1) The Manager, Seattle Aircraft Certification Office (ACO), FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. Send information to Attn: Ivan Li, Aerospace Engineer, Airframe Branch, ANM-120S, FAA, Seattle Aircraft Certification Office (ACO), 1601 Lind Avenue, SW., Renton, Washington 98057-3356; telephone (425) 917-6437; fax (425) 917-6590. Information may be e-mailed to: 9-ANM-Seattle-ACO-AMOC-Requests@faa.gov . (2) To request a different method of compliance or a different compliance time for this AD, follow the procedures in 14 CFR 39.19. Before using any approved AMOC on any airplane to which the AMOC applies, notify your principal maintenance inspector (PMI) or principal avionics inspector (PAI), as appropriate, or lacking a principal inspector, your local Flight Standards District Office. The AMOC approval letter must specifically reference this AD. (3) An AMOC that provides an acceptable level of safety may be used for any repair required by this AD if it is approved by the Boeing Commercial Airplanes Organization Designation Authorization that has been authorized by the Manager, Seattle ACO, to make those findings. For a repair method to be approved, the repair must meet the certification basis of the airplane, and the approval must specifically refer to this AD. Material Incorporated by Reference (k) You must use Boeing Alert Service Bulletin 747-53A2750, dated August 27, 2009, to do the actions required by this AD, unless the AD specifies otherwise. (1) The Director of the Federal Register approved the incorporation by reference of this service information under 5 U.S.C. 552(a) and 1 CFR part 51. (2) For service information identified in this AD, contact Boeing Commercial Airplanes, Attention: Data & Services Management, P.O. Box 3707, MC 2H-65, Seattle, Washington 98124-2207; telephone 206-544-5000, extension 1; fax 206-766-5680; e-mail me.boecom@boeing.com ; Internet https://www.myboeingfleet.com . (3) You may review copies of the service information at the FAA, Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton, Washington. For information on the availability of this material at the FAA, call 425-227-1221. (4) You may also review copies of the service information that is incorporated by reference at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202-741-6030, or go to: http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html. Issued in Renton, Washington, on June 25, 2010. Ali Bahrami, Manager, Transport Airplane Directorate, Aircraft Certification Service. [FR Doc. 2010-16435 Filed 7-12-10; 8:45 am] BILLING CODE 4910-13-P

This AD results from reports of cracks in overwing intercostal webs between station (STA) 1160 and STA 1220. The Federal Aviation Administration is issuing this AD to detect and correct such cracking, which could grow and result in a severed intercostal. If an intercostal is severed, cracks could develop in the adjacent frame structure and skin, resulting in a rapid loss of cabin pressure.