AD 2010-21-14 Airworthiness Directives; PIAGGIO AERO INDUSTRIES S.p.A Model PIAGGIO P-180 Airplanes

Models named: PIAGGIO P-180. Read the applicability below — it usually turns on serial or part numbers too.

This AD applies to PIAGGIO AERO INDUSTRIES S.p.A Model PIAGGIO P-180 airplanes, serial numbers 1166 through 1175, certificated in any category.

Unless already done, within 200 hours time-in-service (TIS) after November 18, 2010 (the effective date of this AD), replace the rivets of the joint brackets on the right-hand and left-hand beam with “Hi-Lok” fasteners, following the accomplishment instructions of PIAGGIO AERO INDUSTRIES S.p.A. Service Bulletin (Mandatory) N.: 80-0268, REV. 0, dated December 18, 2008. FAA AD Differences Note: This AD differs from the MCAI and/or service information as follows: No differences. Other FAA AD Provisions (g) The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, Standards Office, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. Send information to ATTN: Sarjapur Nagarajan, Aerospace Engineer, FAA, Small Airplane Directorate, 901 Locust, Room 301, Kansas City, Missouri 64106; telephone: (816) 329-4145; fax: (816) 329-4090; e-mail: sarjapur.nagarajan@faa.gov. Before using any approved AMOC on any airplane to which the AMOC applies, notify your appropriate principal inspector (PI) in the FAA Flight Standards District Office (FSDO), or lacking a PI, your local FSDO. (2) Airworthy Product: For any requirement in this AD to obtain corrective actions from a manufacturer or other source, use these actions if they are FAA-approved. Corrective actions are considered FAA-approved if they are approved by the State of Design Authority (or their delegated agent). You are required to assure the product is airworthy before it is returned to service. (3) Reporting Requirements: For any reporting requirement in this AD, under the provisions of the Paperwork Reduction Act (44 U.S.C. 3501 et seq. ), the Office of Management and Budget (OMB) has approved the information collection requirements and has assigned OMB Control Number 2120-0056. Related Information (h) Refer to MCAI European Aviation Safety Agency (EASA) AD No.: 2010-0126, dated June 23, 2010; and PIAGGIO AERO INDUSTRIES S.p.A. Service Bulletin (Mandatory) N.: 80-0268, REV. 0, dated December 18, 2008, for related information. Material Incorporated by Reference (i) You must use PIAGGIO AERO INDUSTRIES S.p.A. Service Bulletin (Mandatory) N.: 80-0268, REV. 0, dated December 18, 2008, to do the actions required by this AD, unless the AD specifies otherwise. (1) The Director of the Federal Register approved the incorporation by reference of this service information under 5 U.S.C. 552(a) and 1 CFR part 51. (2) For service information identified in this AD, contact Piaggio Aero Industries S.p.a., Via Cibrario, 4-16154 Genoa, Italy; phone: +39 010 6481 353; fax: +39 010 6481 881; e-mail: airworthiness@piaggioaero.it; Internet: http://www.piaggioaero.com. (3) You may review copies of the service information incorporated by reference for this AD at the FAA, Central Region, Office of the Regional Counsel, 901 Locust, Kansas City, Missouri 64106. For information on the availability of this material at the Central Region, call (816) 329-3768. (4) You may also review copies of the service information incorporated by reference for this AD at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call (202) 741-6030, or go to: http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html. Issued in Kansas City, Missouri, on September 30, 2010. John R. Colomy, Acting Manager, Small Airplane Directorate, Aircraft Certification Service. [FR Doc. 2010-25284 Filed 10-13-10; 8:45 am] BILLING CODE 4910-13-P

Unless already done, within 200 hours time-in-service (TIS) after November 18, 2010 (the effective date of this AD), replace the rivets of the joint brackets on the right-hand and left-hand beam with “Hi-Lok” fasteners, following the accomplishment instructions of PIAGGIO AERO INDUSTRIES S.p.A. Service Bulletin (Mandatory) N.: 80-0268, REV. 0, dated December 18, 2008. FAA AD Differences Note: This AD differs from the MCAI and/or service information as follows: No differences. Other FAA AD Provisions (g) The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, Standards Office, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. Send information to ATTN: Sarjapur Nagarajan, Aerospace Engineer, FAA, Small Airplane Directorate, 901 Locust, Room 301, Kansas City, Missouri 64106; telephone: (816) 329-4145; fax: (816) 329-4090; e-mail: sarjapur.nagarajan@faa.gov. Before using any approved AMOC on any airplane to which the AMOC applies, notify your appropriate principal inspector (PI) in the FAA Flight Standards District Office (FSDO), or lacking a PI, your local FSDO. (2) Airworthy Product: For any requirement in this AD to obtain corrective actions from a manufacturer or other source, use these actions if they are FAA-approved. Corrective actions are considered FAA-approved if they are approved by the State of Design Authority (or their delegated agent). You are required to assure the product is airworthy before it is returned to service. (3) Reporting Requirements: For any reporting requirement in this AD, under the provisions of the Paperwork Reduction Act (44 U.S.C. 3501 et seq. ), the Office of Management and Budget (OMB) has approved the information collection requirements and has assigned OMB Control Number 2120-0056. Related Information (h) Refer to MCAI European Aviation Safety Agency (EASA) AD No.: 2010-0126, dated June 23, 2010; and PIAGGIO AERO INDUSTRIES S.p.A. Service Bulletin (Mandatory) N.: 80-0268, REV. 0, dated December 18, 2008, for related information. Material Incorporated by Reference (i) You must use PIAGGIO AERO INDUSTRIES S.p.A. Service Bulletin (Mandatory) N.: 80-0268, REV. 0, dated December 18, 2008, to do the actions required by this AD, unless the AD specifies otherwise. (1) The Director of the Federal Register approved the incorporation by reference of this service information under 5 U.S.C. 552(a) and 1 CFR part 51. (2) For service information identified in this AD, contact Piaggio Aero Industries S.p.a., Via Cibrario, 4-16154 Genoa, Italy; phone: +39 010 6481 353; fax: +39 010 6481 881; e-mail: airworthiness@piaggioaero.it; Internet: http://www.piaggioaero.com. (3) You may review copies of the service information incorporated by reference for this AD at the FAA, Central Region, Office of the Regional Counsel, 901 Locust, Kansas City, Missouri 64106. For information on the availability of this material at the Central Region, call (816) 329-3768. (4) You may also review copies of the service information incorporated by reference for this AD at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call (202) 741-6030, or go to: http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html. Issued in Kansas City, Missouri, on September 30, 2010. John R. Colomy, Acting Manager, Small Airplane Directorate, Aircraft Certification Service. [FR Doc. 2010-25284 Filed 10-13-10; 8:45 am] BILLING CODE 4910-13-P