AD 2010-23-13 Airworthiness Directives; The Boeing Company Model 757 Airplanes

Models named: 757-200, -200PF, -200CB, -300 series. Read the applicability below — it usually turns on serial or part numbers too.

This AD applies to all The Boeing Company Model 757-200, -200PF, -200CB, and -300 series airplanes, certificated in any category.

You are responsible for having the actions required by this AD performed within the compliance times specified, unless the actions have already been done. Action (g) Within 60 months after the effective date of this AD, change the lower fixed leading edge panel assemblies immediately outboard of the nacelles at slats 4 and 7, in accordance with the Accomplishment Instructions of Boeing Special Attention Service Bulletin 757-57-0070, dated January 27, 2010; except, where the service bulletin specifies washer part number (P/N) NAS11490632J for the modification of the lower fixed leading edge panel assemblies, this AD requires installation of P/N NAS1149D0632J. Alternative Methods of Compliance (AMOCs) (h)(1) The Manager, Seattle Aircraft Certification Office (ACO), FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. Send information to ATTN: Tak Kobayashi, Aerospace Engineer, Propulsion Branch, ANM-140S, FAA, Seattle Aircraft Certification Office, 1601 Lind Avenue, SW., Renton, Washington 98057-3356; telephone (425) 917-6499; fax (425) 917-6590. Information may be e-mailed to: 9-ANM-Seattle-ACO-AMOC-Requests@faa.gov. (2) To request a different method of compliance or a different compliance time for this AD, follow the procedures in 14 CFR 39.19. Before using any approved AMOC on any airplane to which the AMOC applies, notify your principal maintenance inspector (PMI) or principal avionics inspector (PAI), as appropriate, or lacking a principal inspector, your local Flight Standards District Office. The AMOC approval letter must specifically reference this AD. Material Incorporated by Reference (i) You must use Boeing Special Attention Service Bulletin 757-57-0070, dated January 27, 2010, to do the actions required by this AD, unless the AD specifies otherwise. (1) The Director of the Federal Register approved the incorporation by reference of this service information under 5 U.S.C. 552(a) and 1 CFR part 51. (2) For service information identified in this AD, contact Boeing Commercial Airplanes, Attention: Data & Services Management, P.O. Box 3707, MC 2H-65, Seattle, Washington 98124-2207; telephone 206-544-5000, extension 1; fax 206-766-5680; e-mail me.boecom@boeing.com; Internet https://www.myboeingfleet.com. (3) You may review copies of the service information at the FAA, Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton, Washington. For information on the availability of this material at the FAA, call 425-227-1221. (4) You may also review copies of the service information that is incorporated by reference at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202-741-6030, or go to: http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html. Issued in Renton, Washington, on October 23, 2010. Michael Kaszycki, Acting Manager, Transport Airplane Directorate, Aircraft Certification Service. [FR Doc. 2010-28160 Filed 11-8-10; 8:45 am] BILLING CODE 4910-13-P

This AD results from reports of Model 757 airplanes in service that have drain holes and unsealed panel assemblies in the fixed leading edge adjacent to the inboard end of slats 4 and 7 that are too close to the hot portion of the engines. The Federal Aviation Administration is issuing this AD to prevent fuel leaking onto an engine and a consequent fire.