AD 2010-24-06 Airworthiness Directives; Short Brothers PLC Model SD3 Airplanes

Models named: SD3-60 SHERPA, SD3-SHERPA, SD3-30, SD3-60. Read the applicability below — it usually turns on serial or part numbers too.

This AD applies to all Short Brothers PLC Model SD3-60 SHERPA, SD3-SHERPA, SD3-30, and SD3-60 airplanes, certificated in any category. Note 1: This AD requires revisions to certain operator maintenance documents to include new inspections. Compliance with these inspections is required by 14 CFR 91.403(c). For airplanes that have been previously modified, altered, or repaired in the areas addressed by these inspections, the operator may not be able to accomplish the inspections described in the revisions. In this situation, to comply with 14 CFR 91.403(c), the operator must request approval for an alternative method of compliance according to paragraph (m) of this AD. The request should include a description of changes to the required inspections that will ensure the continued damage tolerance of the affected structure. The FAA has provided guidance for this determination in Advisory Circular (AC) 25-1529.

You are responsible for having the actions required by this AD performed within the compliance times specified, unless the actions have already been done. Restatement of Requirements of AD 2006-12-18 Revision of Airplane Flight Manual (AFM) (g) Within 30 days after July 21, 2006 (the effective date of AD 2006-12-18), revise the Limitations and Normal Procedures sections of the AFMs as specified in Table 1 of this AD to include the information in the applicable Shorts advance amendment bulletins as specified in Table 1 of this AD. The advance amendment bulletins address operation during icing conditions and fuel system failures. Thereafter, operate the airplane according to the limitations and procedures in the applicable advance amendment bulletin. Note 2: The requirements of paragraph (g) of this AD may be done by inserting a copy of the applicable advance amendment bulletin into the AFM. When the applicable advance amendment bulletin has been included in general revisions of the AFM, the general revisions may be inserted into the AFM and the advance amendment bulletin may be removed, provided the relevant information in the general revision is identical to that in the advance amendment bulletin. Table 1—AFM Revisions Airplane model— Shorts advance amendment bulletin— AFM— SD3-30 airplanes 1/2004, dated July 13, 2004 SBH.3.2, SBH.3.3, SBH.3.6, SBH.3.7, SBH.3.8, and SB.3.9. SD3-60 airplanes 1/2004, dated July 13, 2004 SB.4.3, SB.4.6, and SB.4.8. SD3-60 SHERPA airplanes 1/2004, dated July 13, 2004 SB.6.2. SD3-SHERPA airplanes 1/2004, dated July 13, 2004 SB.5.2. Revision of Airworthiness Limitation (AWL) Section (h) Within 180 days after July 21, 2006: Revise the AWL section of the Instructions for Continued Airworthiness by incorporating airplane maintenance manual (AMM) Sections 5-20-01 and 5-20-02 as introduced by the Shorts temporary revisions (TR) specified in Table 2 of this AD into the AWL section of the AMMs for the airplane models specified in Table 2 of this AD, except as required by paragraph (j) of this AD. Thereafter, except as provided by paragraph (m)(1) of this AD, no alternative structural inspection intervals may be approved for the longitudinal skin joints in the fuselage shell. Note 3: The requirements of paragraph (h) of this AD may be done by inserting a copy of the applicable TR into the applicable AMM. When the TR has been included in general revisions of the AMM, the general revisions may be inserted in the AMM and the TR may be removed, provided the relevant information in the general revision is identical to that in the TR. Table 2—AMM Temporary Revisions Airplane model— Temporary revision— Date— AMM— SD3-30 airplanes TR330-AMM-13 June 21, 2004 SD3-30 AMM. SD3-30 airplanes TR330-AMM-14 June 21, 2004 SD3-30 AMM. SD3-60 airplanes TR360-AMM-33 July 27, 2004 SD3-60 AMM. SD3-60 airplanes TR360-AMM-34 July 27, 2004 SD3-60 AMM. SD3-60 SHERPA airplanes TRSD360S-AMM-14 July 29, 2004 SD3-60 SHERPA AMM. SD3-60 SHERPA airplanes TRSD360S-AMM-15 July 29, 2004 SD3-60 SHERPA AMM. SD3-SHERPA airplanes TRSD3S-AMM-15 July 28, 2004 SD3 SHERPA AMM. SD3-SHERPA airplanes TRSD3S-AMM-16 July 28, 2004 SD3 SHERPA AMM. Resistance Check, Inspection, and Jumper Installation (i) Within 180 days after July 21, 2006: Perform the insulation resistance check, general visual inspections, and bonding jumper wire installations; in accordance with Shorts Service Bulletin SD330-28-37, SD360-28-23, SD360 SHERPA-28-3, or SD3 SHERPA-28-2; all dated June 2004; as applicable. If any defect or damage is discovered during any inspection or check required by this AD, before further flight, repair the defect or damage using a method approved by the Manager, International Branch, ANM-116, Transport Airplane Directorate, FAA; the Civil Aviation Authority (CAA) (or its delegated agent); or EASA (or its delegated agent). Note 4: For the purposes of this AD, a general visual inspection is: “A visual examination of an interior or exterior area, installation, or assembly to detect obvious damage, failure, or irregularity. This level of inspection is made from within touching distance unless otherwise specified. A mirror may be necessary to ensure visual access to all surfaces in the inspection area. This level of inspection is made under normally available lighting conditions such as daylight, hangar lighting, flashlight, or droplight and may require removal or opening of access panels or doors. Stands, ladders, or platforms may be required to gain proximity to the area being checked.” New Requirements of This AD Revision of AWL Section: New Limitations and CDCCLs (j) Within 90 days after the effective date of this AD: Revise the AWL section of the Instructions for Continued Airworthiness by incorporating maintenance manual Sections 5-20-01 and 5-20-02 as introduced by the Bombardier and Shorts TRs specified in Table 3 of this AD into the AWL section of the maintenance manuals for the airplane models specified in Table 3 of this AD. Doing this revision terminates the requirement to incorporate the temporary revisions specified in paragraph (h) of this AD. After doing this revision the temporary revisions required by paragraph (h) of this AD may be removed. Table 3—Newly Required Maintenance Manual Temporary Revisions Model— Temporary revision— Date— Manual— SD3-30 airplanes Shorts TR TR330-AMM-35 June 6, 2006 Shorts SD3-30 Maintenance Manual (MM). SD3-30 airplanes Shorts TR TR330-AMM-36 June 6, 2006 Shorts SD3-30 MM. SD3-60 airplanes Bombardier TR TR360-AMM-55 November 11, 2005 Bombardier SD3-60 AMM. SD3-60 airplanes Bombardier TR TR360-AMM-56 November 11, 2005 Bombardier SD3-60 AMM. SD3-60 SHERPA airplanes Shorts TR TRSD360S-AMM-35 June 27, 2006 Shorts SD3-60 SHERPA MM. SD3-60 SHERPA airplanes Shorts TR TRSD360S-AMM-36 June 27, 2006 Shorts SD3-60 SHERPA MM. SD3-SHERPA airplanes Shorts TR TRSD3S-AMM-36 June 19, 2006 Shorts SD3-SHERPA MM. SD3-SHERPA airplanes Shorts TR TRSD3S-AMM-37 June 19, 2006 Shorts SD3-SHERPA MM. Note 5: The requirements of paragraph (j) of this AD may be done by inserting a copy of the applicable TR into the applicable maintenance manual. When the TR has been included in general revisions of the AMM, the general revisions may be inserted in the AMM and the TR may be removed, provided the relevant information in the general revision is identical to that in the TR. (k) After accomplishing the actions specified in paragraph (j) of this AD, no alternative inspections, inspection intervals, or CDCCLs may be used unless the inspections, intervals, or CDCCLs are approved as an alternative method of compliance (AMOC), in accordance with the procedures specified in paragraph (m) of this AD. Explanation of CDCCL Requirements Note 6: Notwithstanding any other maintenance or operational requirements, components that have been identified as airworthy or installed on the affected airplanes before the revision of the AMM, as required by paragraph (h) or (j) of this AD, do not need to be reworked in accordance with the CDCCLs. However, once the AMM has been revised, future maintenance actions on these components must be done in accordance with the CDCCLs. Credit for Actions Accomplished in Accordance With Other Service Information (l) Revising the AFM, as required by paragraph (g) of this AD, by inserting Shorts Advance Amendment Bulletin 1/2004, dated 7/13/04, for Model SD3-60 Sherpa airplanes, into AFM SB.5.2; or Shorts Advance Amendment Bulletin 1/2004, dated 7/13/04, for Model SD3-sherpa airplanes, into AFM SB.6.2; before the effective date of this AD is acceptable for compliance with the AFM revision required by paragraph (g) of this AD. FAA AD Differences Note 7: This AD differs from the MCAI and/or service information as follows: No differences. Other FAA AD Provisions (m) The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, International Branch, ANM-116, Transport Airplane Directorate, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. Send information to ATTN: Todd Thompson, Aerospace Engineer, International Branch, ANM-116, Transport Airplane Directorate, FAA, 1601 Lind Avenue, SW., Renton, Washington 98057-3356; telephone (425) 227-1175; fax (425) 227-1149. Before using any approved AMOC on any airplane to which the AMOC applies, notify your principal maintenance inspector (PMI) or principal avionics inspector (PAI), as appropriate, or lacking a principal inspector, your local Flight Standards District Office. The AMOC approval letter must specifically reference this AD. (2) Airworthy Product: For any requirement in this AD to obtain corrective actions from a manufacturer or other source, use these actions if they are FAA-approved. Corrective actions are considered FAA-approved if they are approved by the State of Design Authority (or their delegated agent). You are required to assure the product is airworthy before it is returned to service. (3) Reporting Requirements: A Federal agency may not conduct or sponsor, and a person is not required to respond to, nor shall a person be subject to a penalty for failure to comply with a collection of information subject to the requirements of the Paperwork Reduction Act unless that collection of information displays a current valid OMB Control Number. The OMB Control Number for this information collection is 2120-0056. Public reporting for this collection of information is estimated to be approximately 5 minutes per response, including the time for reviewing instructions, completing and reviewing the collection of information. All responses to this collection of information are mandatory. Comments concerning the accuracy of this burden and suggestions for reducing the burden should be directed to the FAA at: 800 Independence Ave., SW., Washington, DC 20591, Attn: Information Collection Clearance Officer, AES-200. Related Information (n) Refer to MCAI EASA Airworthiness Directive 2006-0198, dated July 11, 2006; Shorts Service Bulletins SD330-28-37, SD360-28-23, SD360 SHERPA-28-3, and SD3 SHERPA-28-2, all dated June 2004; and the service information listed in Tables 1, 2, and 3 of this AD; for related information. Material Incorporated by Reference (o) You must use the service information contained in Table 4 of this AD, as applicable, to do the actions required by this AD, unless the AD specifies otherwise. Table 4—All Material Incorporated by Reference Document Date Manual Shorts Advance Amendment Bulletin 1/2004 July 13, 2004 Shorts Airplane Flight Manuals (AFMs) SBH.3.2, SBH.3.3, SBH.3.6, SBH.3.7, SBH.3.8, and SB.3.9. Shorts Advance Amendment Bulletin 1/2004 July 13, 2004 Shorts AFMs SB.4.3, SB.4.6, and SB.4.8. Shorts Advance Amendment Bulletin 1/2004 July 13, 2004 Shorts AFM SB.5.2. Shorts Advance Amendment Bulletin 1/2004 July 13, 2004 Shorts AFM SB.6.2. Shorts TR330-AMM-13 June 21, 2004 Shorts SD3-30 Airplane Maintenance Manual (AMM). Shorts TR330-AMM-14 June 21, 2004 Shorts SD3-30 AMM. Shorts TR360-AMM-33 July 27, 2004 Shorts SD3-60 AMM. Shorts TR360-AMM-34 July 27, 2004 Shorts SD3-60 AMM. Shorts TRSD360S-AMM-14 July 29, 2004 Shorts SD3-60 SHERPA AMM. Shorts TRSD360S-AMM-15 July 29, 2004 Shorts SD3-60 SHERPA AMM. Shorts TRSD3S-AMM-15 July 28, 2004 Shorts SD3 SHERPA AMM. Shorts TRSD3S-AMM-16 July 28, 2004 Shorts SD3 SHERPA AMM. Shorts Service Bulletin SD330-28-37 June 2004 None. Shorts Service Bulletin SD360-28-23 June 2004 None. Shorts Service Bulletin SD360 SHERPA-28-3 June 2004 None. Shorts Service Bulletin SD3 SHERPA-28-2 June 2004 None. Shorts TR TR330-AMM-35 June 6, 2006 Shorts SD3-30 Maintenance Manual (MM). Shorts TR TR330-AMM-36 June 6, 2006 Shorts SD3-30 MM. Bombardier TR TR360-AMM-55 November 11, 2005 Bombardier SD3-60 AMM. Bombardier TR TR360-AMM-56 November 11, 2005 Bombardier SD3-60 AMM. Shorts TR TRSD360S-AMM-35 June 27, 2006 Shorts SD3-60 SHERPA MM. Shorts TR TRSD360S-AMM-36 June 27, 2006 Shorts SD3-60 SHERPA MM. Shorts TR TRSD3S-AMM-36 June 19, 2006 Shorts SD3-SHERPA MM. Shorts TR TRSD3S-AMM-37 June 19, 2006 Shorts SD3-SHERPA MM. (1) The Director of the Federal Register approved the incorporation by reference of the service information contained in Table 5 of this AD under 5 U.S.C. 552(a) and 1 CFR part 51. Table 5—New Material Incorporated by Reference Document Date Manual Shorts TR TR330-AMM-35 June 6, 2006 Shorts SD3-30 MM. Shorts TR TR330-AMM-36 June 6, 2006 Shorts SD3-30 MM. Bombardier TR TR360-AMM-55 November 11, 2005 Bombardier SD3-60 AMM. Bombardier TR TR360-AMM-56 November 11, 2005 Bombardier SD3-60 AMM. Shorts TR TRSD360S-AMM-35 June 27, 2006 Shorts SD3-60 SHERPA MM. Shorts TR TRSD360S-AMM-36 June 27, 2006 Shorts SD3-60 SHERPA MM. Shorts TR TRSD3S-AMM-36 June 19, 2006 Shorts SD3-SHERPA MM. Shorts TR TRSD3S-AMM-37 June 19, 2006 Shorts SD3-SHERPA MM. (2) The Director of the Federal Register previously approved the incorporation by reference of the service information contained in Table 6 of this AD on July 21, 2006 (71 FR 34801, June 16, 2006). Table 6—Material Previously Incorporated by Reference Document Date Manual Shorts Advance Amendment Bulletin 1/2004 July 13, 2004 Shorts Airplane Flight Manuals (AFMs) SBH.3.2, SBH.3.3, SBH.3.6, SBH.3.7, SBH.3.8, and SB.3.9. Shorts Advance Amendment Bulletin 1/2004 July 13, 2004 Shorts AFMs SB.4.3, SB.4.6, and SB.4.8. Shorts Advance Amendment Bulletin 1/2004 July 13, 2004 Shorts AFM SB.5.2. Shorts Advance Amendment Bulletin 1/2004 July 13, 2004 Shorts AFM SB.6.2. Shorts Temporary Revision TR330-AMM-13 June 21, 2004 SD3-30 AMM. Shorts Temporary Revision TR330-AMM-14 June 21, 2004 SD3-30 AMM. Shorts Temporary Revision TR360-AMM-33 July 27, 2004 SD3-60 AMM. Shorts Temporary Revision TR360-AMM-34 July 27, 2004 SD3-60 AMM. Shorts Temporary Revision TRSD360S-AMM-14 July 29, 2004 SD3-60 SHERPA AMM. Shorts Temporary Revision TRSD360S-AMM-15 July 29, 2004 SD3-60 SHERPA AMM. Shorts Temporary Revision TRSD3S-AMM-15 July 28, 2004 SD3 SHERPA AMM. Shorts Temporary Revision TRSD3S-AMM-16 July 28, 2004 SD3 SHERPA AMM. Shorts Service Bulletin SD330-28-37 June 2004 None. Shorts Service Bulletin SD360-28-23 June 2004 None. Shorts Service Bulletin SD360 SHERPA-28-3 June 2004 None. Shorts Service Bulletin SD3 SHERPA-28-2 June 2004 None. (3) For service information identified in this AD, contact Short Brothers PLC, Airworthiness, P.O. Box 241, Airport Road, Belfast, BT3 9DZ Northern Ireland; telephone +44(0)2890-462469; fax +44(0)2890-468444; e-mail michael.mulholland@aero.bombardier.com; Internet http://www.bombardier.com. (4) You may review copies of the service information at the FAA, Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton, Washington. For information on the availability of this material at the FAA, call 425-227-1221. (5) You may also review copies of the service information that is incorporated by reference at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202-741-6030, or go to: http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html. Issued in Renton, Washington, on November 10, 2010. Jeffrey E. Duven, Acting Manager, Transport Airplane Directorate, Aircraft Certification Service. [FR Doc. 2011-30 Filed 1-11-11; 8:45 am] BILLING CODE 4910-13-P