AD 2011-15-01 Airworthiness Directives; The Boeing Company Model DC-9-81 (MD-81), DC-9-82 (MD-82), DC-9-83 (MD-83), DC-9-87 (MD-87), and MD-88 Airplanes

This AD applies to The Boeing Company Model DC-9-81 (MD-81), DC-9-82 (MD-82), DC-9-83 (MD-83), DC-9-87 (MD-87), and MD-88 airplanes, certificated in any category, as identified in Boeing Alert Service Bulletin MD80-55A067, dated June 24, 2010.

Comply with this AD within the compliance times specified, unless already done. Inspections (g) Within 4,500 flight cycles after the effective date of this AD, do a detailed inspection for distress in and existing repairs to the leading edge structure of the vertical stabilizer at the splice at Station Zfs=52.267, in accordance with the Accomplishment Instructions of Boeing Alert Service Bulletin MD80-55A067, dated June 24, 2010. Repetitive Inspections for Cracks, and Related Investigative and Corrective Actions (h) Before further flight after doing the inspection required by paragraph (g) of this AD, inspect for cracks of the left and right vertical stabilizer front spar cap, in accordance with either Option 1 or Option 2 as specified in the Accomplishment Instructions of Boeing Alert Service Bulletin MD80-55A067, dated June 24, 2010. If any crack is found, before further flight, evaluate and verify to confirm all crack indications, in accordance with the Accomplishment Instructions of Boeing Alert Service Bulletin MD80-55A067, dated June 24, 2010. (1) If any cracking is confirmed, before further flight, repair using a method approved in accordance with the procedures specified in paragraph (l) of this AD. (2) If no cracking is confirmed, repeat the inspection thereafter at intervals not to exceed the applicable interval specified in paragraph (h)(2)(i) or (h)(2)(ii) of this AD. (i) If the most recent inspection was done using Option 1, the next inspection must be done within 4,400 flight cycles. (ii) If the most recent inspection was done using Option 2, the next inspection must be done within 3,000 flight cycles. Leading Edge Repair (i) If leading edge distress is found during the detailed inspection required by paragraph (g) of this AD, before further flight and after accomplishing the inspection required by paragraph (h) of this AD, repair the leading edge, in accordance with the Accomplishment Instructions of Boeing Alert Service Bulletin MD80-55A067, dated June 24, 2010. Inspection for Loose/Missing Fasteners (j) For airplanes on which no cracking is confirmed during the initial inspection required by paragraph (h) of this AD: At the applicable time specified in paragraph (j)(1) or (j)(2) of this AD, do a detailed inspection for indications of loose and missing fasteners, in accordance with the Accomplishment Instructions of Boeing Alert Service Bulletin MD80-55A067, dated June 24, 2010. If any loose or missing fastener is found, before further flight, repair the leading edge, in accordance with the Accomplishment Instructions of Boeing Alert Service Bulletin MD80-55A067, dated June 24, 2010. (1) If the inspection required by paragraph (h) was done using Option 1, do the inspection required by paragraph (j) of this AD within 4,400 flight cycles after accomplishing the inspection required by paragraph (h) of this AD. (2) If inspection required by paragraph (h) was done using Option 2, do the inspection required by paragraph (j) of this AD within 3,000 flight cycles after accomplishing the inspection required by paragraph (h) of this AD. (k) For airplanes on which no cracking is confirmed during the most recent inspection required by paragraph (h) of this AD: Repeat the inspection for loose and missing fasteners required by paragraph (j) of this AD thereafter at intervals not to exceed the applicable time specified in paragraph (k)(1) or (k)(2) of this AD. (1) If the most recent inspection required by paragraph (h) was done using Option 1, the next inspection required by paragraph (j) of this AD must be done within 4,400 flight cycles after accomplishing the most recent inspection required by paragraph (j) of this AD. (2) If the most recent inspection required by paragraph (h) was done using Option 2, the next inspection required by paragraph (j) of this AD must be done within 3,000 flight cycles after the most recent inspection required by paragraph (j) of this AD. Alternative Methods of Compliance (AMOCs) (l)(1) The Manager, Los Angeles Aircraft Certification Office (ACO), FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or local Flight Standards District Office, as appropriate. If sending information directly to the manager of the ACO, send it to the attention of the person identified in the Related Information section of this AD. (2) Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local flight standards district office/certificate holding district office. (3) An AMOC that provides an acceptable level of safety may be used for any repair required by this AD if it is approved by the Boeing Commercial Airplanes Organization Designation Authorization (ODA) that has been authorized by the Manager, Los Angeles ACO to make those findings. For a repair method to be approved, the repair must meet the certification basis of the airplane and 14 CFR 25.571, Amendment 45, and the approval must specifically refer to this AD. Related Information (m) For more information about this AD, contact Roger Durbin, Aerospace Engineer, Airframe Branch, ANM-120L, Los Angeles Aircraft Certification Office, 3960 Paramount Boulevard, Lakewood, California 90712-4137; phone: 562-627-5233; fax: 562-627-5210; e-mail: Roger.Durbin@faa.gov. Material Incorporated by Reference (n) You must use Boeing Alert Service Bulletin MD80-55A067, dated June 24, 2010, to do the actions required by this AD, unless the AD specifies otherwise. (1) The Director of the Federal Register approved the incorporation by reference of this service information under 5 U.S.C. 552(a) and 1 CFR part 51. (2) For service information identified in this AD, contact Boeing Commercial Airplanes, Attention: Data & Services Management, 3855 Lakewood Boulevard, MC D800-0019, Long Beach, California 90846-0001; telephone 206-544-5000, extension 2; fax 206-766-5683; e-mail dse.boecom@boeing.com ; Internet https://www.myboeingfleet.com. (3) You may review copies of the service information at the FAA, Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton, Washington. For information on the availability of this material at the FAA, call 425-227-1221. (4) You may also review copies of the service information that is incorporated by reference at the National Archives and Records Administration (NARA). For information on the availability of this material at an NARA facility, call 202-741-6030, or go to http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html. Issued in Renton, Washington, on July 1, 2011. Jeffrey E. Duven, Acting Manager, Transport Airplane Directorate, Aircraft Certification Service. [FR Doc. 2011-17400 Filed 7-14-11; 8:45 am] BILLING CODE 4910-13-P

This AD was prompted by reports of cracked vertical stabilizer skin, a severed front spar cap, elongated fastener holes at the leading edge of the vertical stabilizer, and a cracked front spar web and front spar cap bolt holes in the vertical stabilizer. We are issuing this AD to detect and correct such cracking damage, which could result in the structure being unable to support limit load, and could lead to the loss of the vertical stabilizer.