AD 2012-19-01 Airworthiness Directives; Lycoming Engines Reciprocating Engines

Makes named: lycoming. Read the applicability below — it usually turns on serial or part numbers too.

This AD applies to Lycoming Engines (L)O-360, (L)IO-360, AEIO-360, IO-390, AEIO-390, O-540, IO-540, AEIO-540, (L)TIO-540, IO-580, AEIO-580, and IO-720 series reciprocating engines listed by engine model number and serial number in Table 1, Table 2, Table 3, or Table 4 of Lycoming Mandatory Service Bulletin (MSB) 569A, dated April 11, 2006, and those engines with crankshafts listed by crankshaft serial number in Table 5 of Lycoming MSB 569A, dated April 11, 2006. These applicable engines are manufactured new, rebuilt, overhauled, or had a crankshaft installed after January 1, 1997, according to Supplement No. 1 to Lycoming MSB No. 569A, dated May 27, 2009.

If you did not previously comply with AD 2006-20-09 or with MSB No. 569A, do the following: (1) If Table 1, Table 2, Table 3, or Table 4 of Lycoming MSB No. 569A, dated April 11, 2006, lists your engine serial number (S/N), and Table 5 of MSB No. 569A, dated April 11, 2006, lists your crankshaft S/N, replace the affected crankshaft with a crankshaft that is not listed in Table 5 of MSB No. 569A at the earliest of the following: (i) The time of the next engine overhaul as specified in Lycoming Service Instruction No. 1009AU, dated November 18, 2009; or (ii) The next separation of the crankcase, or (iii) No later than 12 years from the time the crankshaft first entered service or was last overhauled, whichever is later. (2) If Table 1, Table 2, Table 3, or Table 4 of Lycoming MSB No. 569A, dated April 11, 2006, does not list your engine S/N, and Table 5 of MSB No. 569A does list your crankshaft S/N (an affected crankshaft was installed as a replacement), replace the affected crankshaft with a crankshaft that is not listed in Table 5 of MSB No. 569A at the earliest of the following: (i) The time of the next engine overhaul as specified in Lycoming Service Instruction No. 1009AU, dated November 18, 2009; or (ii) The next separation of the crankcase, or (iii) No later than 12 years from the time the crankshaft first entered service or was last overhauled, whichever is later.

(1) If you previously complied with AD 2006-20-09 (71 FR 57407, September 29, 2006), no further action is required. (2) If you previously accomplished Lycoming MSB No. 569A, no further action is required. (3) If Lycoming Engines manufactured new, rebuilt, overhauled, or repaired your engine, or replaced the crankshaft in your engine before January 1, 1997, and you have not had the crankshaft replaced, no further action is required. (4) If Table 1, Table 2, Table 3, or Table 4 of Lycoming MSB No. 569A, dated April 11, 2006, lists your engine S/N, and Table 5 of MSB No. 569A, dated April 11, 2006, does not list your crankshaft S/N, no further action is required. (5) For engine model TIO-540-U2A, S/N L-4641-61A, no action is required.

You are responsible for having the actions required by this AD performed within the compliance times specified unless the actions have already been done.

This AD supersedes AD 2006-20-09 (71 FR 57407, September 29, 2006).