AD 2013-03-10 Airworthiness Directives; Lindstrand Hot Air Balloons Ltd Appliances

This AD applies to all hot air balloons, certificated in any category, equipped with Lindstrand Hot Air Balloons Ltd female ACME threaded hose connectors, part numbers (P/Ns) HS6139 and HS6144, all serial numbers.

Unless already done, do the following actions: (1) Within the next 60 days after March 19, 2013 (the effective date of this AD), inspect the female ACME threaded hose connectors, (P/Ns) HS6139 and HS6144, for leaking following the Accomplishment Instructions of Lindstrand Hot Air Balloons Ltd Service Bulletin No. 12, Issue 2, dated May 10, 2012. (2) If fuel leakage is detected in the inspection required in paragraph (f)(1) of this AD, before further flight, tighten the threaded hose connector to the correct torque following Lindstrand Hot Air Balloons Ltd Service Bulletin No. 12, Issue 2, dated May 10, 2012. (3) If, after March 19, 2013 (the effective date of this AD), you install on any balloon an ACME threaded hose connector, (P/Ns) HS6139 or HS6144, manufactured by Lindstrand Hot Air Balloons Ltd and supplied as a spare part between January 1, 2011, and September 1, 2011, before further flight, you must comply with the actions of this AD. (4) Although the European Aviation Safety Agency (EASA) MCAI allows the pilot-owner to do the inspection and correction required in paragraphs (f)(1), (f)(2), and (f)(3) of this AD, the U.S. regulatory system requires all actions of this AD be done by a certified mechanic.

The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, Standards Office, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. Send information to ATTN: Taylor Martin, Aerospace Engineer, FAA, Small Airplane Directorate, 901 Locust, Room 301, Kansas City, Missouri 64106; telephone: (816) 329-4138; fax: (816) 329-4090; email: taylor.martin@faa.gov. Before using any approved AMOC on any airplane to which the AMOC applies, notify your appropriate principal inspector (PI) in the FAA Flight Standards District Office (FSDO), or lacking a PI, your local FSDO. (2) Airworthy Product: For any requirement in this AD to obtain corrective actions from a manufacturer or other source, use these actions if they are FAA-approved. Corrective actions are considered FAA-approved if they are approved by the State of Design Authority (or their delegated agent). You are required to assure the product is airworthy before it is returned to service. (3) Reporting Requirements: For any reporting requirement in this AD, a federal agency may not conduct or sponsor, and a person is not required to respond to, nor shall a person be subject to a penalty for failure to comply with a collection of information subject to the requirements of the Paperwork Reduction Act unless that collection of information displays a current valid OMB Control Number. The OMB Control Number for this information collection is 2120-0056. Public reporting for this collection of information is estimated to be approximately 5 minutes per response, including the time for reviewing instructions, completing and reviewing the collection of information. All responses to this collection of information are mandatory. Comments concerning the accuracy of this burden and suggestions for reducing the burden should be directed to the FAA at: 800 Independence Ave. SW., Washington, DC 20591, Attn: Information Collection Clearance Officer, AES-200.

This AD was prompted by mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as insufficient tightness of the threaded hose connector in the assembly area that could result in fuel leakage. We are issuing this AD to detect and correct insufficient tightness of the threaded hose connector in the assembly area. This condition, if not corrected, could result in fuel leakage and lead to an inflight fire.

None.