Airworthiness directives › 2014-04-01
AD 2014-04-01 Airworthiness Directives; Slingsby Aviation Ltd. Airplanes
Models named: T67M260. Read the applicability below — it usually turns on serial or part numbers too.
Applicability*9
This AD applies to Slingsby Aviation Ltd. Model T67M260 airplanes, all serial numbers, certificated in any category.
Compliance
Unless already done, do the actions specified in paragraphs (f)(1) through (f)(4) of this AD: (1) Within the next 150 hours time-in-service (TIS) after April 1, 2014 (the effective date of this AD) or at the next annual inspection after April 1, 2014 (the effective date of this AD), whichever occurs later, and repetitively thereafter at intervals not to exceed 150 hours TIS, inspect the aluminum horizontal stabilizer attachment brackets for cracks. Do the inspections following the ACTION instructions in Slingsby Advanced Composites Ltd. Service Bulletin S.B. No: 179, Issue 4, dated March 15, 2007. (2) If any cracks are found during any inspection required in paragraph (f)(1) of this AD, before further flight, replace the cracked bracket with a serviceable part. Do the replacement following the ACTION instructions in Slingsby Advanced Composites Ltd. Service Bulletin S.B. No: 179, Issue 4, dated March 15, 2007. If a serviceable aluminum horizontal stabilizer attachment bracket is used as a replacement part, repetitively inspect as specified in paragraph (f)(1) of this AD. (3) To terminate the repetitive inspections required in paragraph (f)(1) of this AD, all four aluminum horizontal stabilizer attachment brackets must be replaced with titanium horizontal stabilizer attachment brackets. (4) After installing titanium horizontal stabilizer attachment brackets, installing aluminum horizontal stabilizer attachment brackets is prohibited.
Required actions
The following provisions also apply to this AD: (1) Alternative Methods of Compliance (AMOCs): The Manager, Standards Office, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. Send information to ATTN: Mike Kiesov, Aerospace Engineer, FAA, Small Airplane Directorate, 901 Locust, Room 301, Kansas City, Missouri 64106; telephone: (816) 329-4144; fax: (816) 329-4090; email: mike.kiesov@faa.gov . Before using any approved AMOC on any airplane to which the AMOC applies, notify your appropriate principal inspector (PI) in the FAA Flight Standards District Office (FSDO), or lacking a PI, your local FSDO. (2) Airworthy Product: For any requirement in this AD to obtain corrective actions from a manufacturer or other source, use these actions if they are FAA-approved. Corrective actions are considered FAA-approved if they are approved by the State of Design Authority (or their delegated agent). You are required to assure the product is airworthy before it is returned to service. (3) Reporting Requirements: For any reporting requirement in this AD, a federal agency may not conduct or sponsor, and a person is not required to respond to, nor shall a person be subject to a penalty for failure to comply with a collection of information subject to the requirements of the Paperwork Reduction Act unless that collection of information displays a current valid OMB Control Number. The OMB Control Number for this information collection is 2120-0056. Public reporting for this collection of information is estimated to be approximately 5 minutes per response, including the time for reviewing instructions, completing and reviewing the collection of information. All responses to this collection of information are mandatory. Comments concerning the accuracy of this burden and suggestions for reducing the burden should be directed to the FAA at: 800 Independence Ave. SW., Washington, DC 20591, Attn: Information Collection Clearance Officer, AES-200.
Unsafe condition
This AD was prompted by mandatory continuing airworthiness information (MCAI) originated by an aviation authority of another country to identify and correct an unsafe condition on an aviation product. The MCAI describes the unsafe condition as cracked horizontal stabilizer attachment brackets. We are issuing this AD to prevent separation of the horizontal stabilizer, which could result in loss of control.
Affected ADs
None.
Read the original on the Federal Register →
You just looked this one up by hand
TrackAD holds all 12,278 of them and matches them against the aircraft you actually look after — airframe, engine, propeller and appliances in one pass — then works out what falls due and when.
- Bring your existing list in from a spreadsheet Paste the rows straight out of Excel. Headers like C/W Date and N/A are read for you.
- A copy that works when this does not One file. No internet, no login, no this software running. For the morning something has to be produced and the computer is not cooperating.
- $5 a month, or $50 a year Up to 50 aircraft on either.
Look round a real shop first Start free
The demonstration shop is eleven real aircraft with a year of work behind them. No account needed.
The directive text above is reproduced from the Federal Register, a work of the United States government and in the public domain. The separation into applicability, compliance and required actions is TrackAD's.*1