AD 2016-16-12 Airworthiness Directives; Continental Motors, Inc. Reciprocating Engines

Makes named: continental. Read the applicability below — it usually turns on serial or part numbers too.

This AD applies to all Continental Motors, Inc. (CMI) model -520 and -550 reciprocating engines, and to all other CMI engine models approved for the use of model -520 and -550 cylinder assemblies such as the CMI model -470 when modified by supplemental type certificate (STC), with Continental Motors Inc., San Antonio (formerly Airmotive Engineering Corp.), replacement parts manufacturer approval (PMA) cylinder assemblies, marketed by Engine Components International Division (hereinafter referred to as ECi), part number (P/N) AEC 631397, with ECi Class 71 or Class 76, serial number (S/N) 1 through S/N 61176, installed.

After the effective date of this AD: (1) Do not repair, or reinstall onto any engine, any cylinder assembly removed per this AD. (2) Do not install any affected ECi cylinder assembly that has been overhauled, into any engine. (3) Do not install any engine that has one or more affected overhauled ECi cylinder assemblies, onto any aircraft. (4) Do not return to service any aircraft that has an engine installed with an ECi cylinder assembly subject to this AD, if the cylinder assembly has 1,000 or more operating hours TIS.

The Manager, Delegation Systems Certification Office or Fort Worth Aircraft Certification Office, may approve AMOCs for this AD. Use the procedures found in 14 CFR 39.19 to make your request.

Comply with this AD within the compliance times specified, unless already done. (1) Review the engine maintenance records to determine if any affected cylinder assemblies are installed. (2) If you cannot determine based on review of engine maintenance records if any affected cylinder assemblies are installed, comply with paragraph (e)(4) of this AD. (3) If you do not have any of the affected ECi cylinder assemblies installed on your engine, no further action is required. (4) Cylinder Identification and Serial Number Location (i) Check the cylinder assembly P/N and Class number. The ECi cylinder assembly, P/N AEC 631397, Class 71 or Class 76, is stamped on the bottom flange of the cylinder barrel. Guidance on the P/N and Class number description and location can be found in ECi Service Instruction No. 99-8-1, Revision 9, dated February 23, 2009. (ii) If you cannot see the cylinder assembly P/N when the cylinder assembly is installed on the engine, you may use the following alternative method of identification: (A) Remove the cylinder assembly rocker box cover. (B) Find the letters ECi, cast into the cylinder head between the valve stems. (C) Check the cylinder head casting P/N. Affected cylinder assemblies have the cylinder head casting, P/N AEC 65385, cast into the cylinder head between the valve stems. (D) Find the cylinder assembly S/N as specified in paragraphs (e)(4)(iii) or (e)(4)(iv) of this AD, as applicable. (iii) For ECi cylinder assemblies, P/N AEC 631397, manufactured through 2008, find the cylinder assembly S/N stamped on the intake port boss two inches down from the top edge of the head. (iv) For ECi cylinder assemblies, P/N AEC 631397, manufactured on or after January 1, 2009, find the cylinder assembly S/N stamped just below the top edge of the head on the exhaust port side. (5) Removal From Service (i) For any affected cylinder assembly with 680 or fewer operating hours time-in-service (TIS) since new on the effective date of this AD, remove the cylinder assembly from service before reaching 1,000 operating hours TIS since new. (ii) For any affected cylinder assembly with more than 680 operating hours TIS since new and 1,000 or fewer operating hours TIS since new on the effective date of this AD, remove the cylinder assembly from service within the next 320 operating hours TIS or within 1,160 operating hours TIS since new, whichever occurs first. (iii) For any affected cylinder assembly with more than 1,000 operating hours TIS since new on the effective date of this AD, remove the cylinder assembly from service within the next 160 operating hours or at next engine overhaul, whichever occurs first. (iv) For any affected cylinder assembly that has been overhauled, remove the cylinder assembly from service within the next 80 operating hours TIS after the effective date of this AD.

None.