TrackAD

Airworthiness directives › 2016-18-15

AD 2016-18-15 Airworthiness Directives; The Boeing Company Airplanes

2016-10-13
2016-09-08
39-18646
FAA-2016-6901
Airframe
—

Models named: 737-600, -700, -700C, -800, -900 series. Read the applicability below — it usually turns on serial or part numbers too.

Applicability*9

(1) This AD applies to The Boeing Company Model 737-600, -700, -700C, -800, and -900 series airplanes, certificated in any category, line number 1 through 1755, as identified in Boeing Alert Service Bulletin 737-53A1248, Revision 2, dated October 14, 2015. (2) Installation of Supplemental Type Certificate (STC) ST00830SE ( http://rgl.faa.gov/Regulatory_and_Guidance_Library/rgSTC.nsf/0/38B606833BBD98B386257FAA00602538?OpenDocument&Highlight=st00830se ) does not affect the ability to accomplish the actions required by this AD. Therefore, for airplanes on which STC ST00830SE is installed, a “change in product” alternative method of compliance (AMOC) approval request is not necessary to comply with the requirements of 14 CFR 39.17.

Compliance

Comply with this AD within the compliance times specified, unless already done.

Required actions

At the applicable time specified in paragraph 1.E., “Compliance,” of Boeing Alert Service Bulletin 737-53A1248, Revision 2, dated October 14, 2015, or within 18 months after November 25, 2005 (the effective date of AD 2005-21-06), whichever occurs later: Do a low frequency eddy current (LFEC) or high frequency eddy current (HFEC) inspection, and a detailed inspection, of the aft and forward sides, as applicable, of the aft pressure bulkhead web at the Y chord, above and below stringer S-15L and stringer S-15R, to detect discrepancies (including cracking, crack indications, discrepant fastener holes, and corrosion), in accordance with the Accomplishment Instructions of Boeing Alert Service Bulletin 737-53A1248, Revision 2, dated October 14, 2015. Access and restoration procedures specified in the Accomplishment Instructions of Boeing Alert Service Bulletin 737-53A1248, Revision 2, dated October 14, 2015, are not required by this AD. Operators may do those procedures following their maintenance practices. (1) If no discrepancy is found: Repeat the inspections thereafter at the applicable times specified in paragraph 1.E., “Compliance,” of Boeing Alert Service Bulletin 737-53A1248, Revision 2, dated October 14, 2015. (2) If any discrepancy is found: Do the actions specified in paragraphs (g)(2)(i) and (g)(2)(ii) of this AD. (i) Repair the discrepancy before further flight using a method approved in accordance with the procedures specified in paragraph (j) of this AD. (ii) On areas that are not repaired, repeat the inspections thereafter at the applicable times specified in paragraph 1.E., “Compliance,” of Boeing Alert Service Bulletin 737-53A1248, Revision 2, dated October 14, 2015.

Unsafe condition

This AD was prompted by an evaluation by the design approval holder (DAH) indicating that the aft pressure bulkhead is subject to widespread fatigue damage (WFD). We are issuing this AD to detect and correct cracks in the aft pressure bulkhead web, which could result in an uncontrolled decompression of the fuselage.

Affected ADs

Certain requirements of this AD terminate certain requirements of AD 2005-21-06, Amendment 39-14344 (70 FR 61226, October 21, 2005) (“AD 2005-21-06”).

Read the original on the Federal Register →

You just looked this one up by hand

TrackAD holds all 12,278 of them and matches them against the aircraft you actually look after — airframe, engine, propeller and appliances in one pass — then works out what falls due and when.

Look round a real shop first Start free

The demonstration shop is eleven real aircraft with a year of work behind them. No account needed.

The directive text above is reproduced from the Federal Register, a work of the United States government and in the public domain. The separation into applicability, compliance and required actions is TrackAD's.*1