Airworthiness directives › 2016-22-07
AD 2016-22-07 Airworthiness Directives; Bell Helicopter Textron
Applicability*9
This AD supersedes AD 75-26-05, Amendment 39-2457 (40 FR 57783, December 12, 1975).
Compliance
(1) Within 25 hours time-in-service (TIS) or 2 weeks, whichever occurs first, and thereafter at intervals not to exceed 25 hours TIS or 2 weeks, whichever occurs first, clean the upper and lower exposed surfaces of each M/R blade from an area starting at the butt end of the blade to three inches outboard of the doublers. Using a 3X or higher power magnifying glass and a light, inspect as follows: (i) Visually inspect the exposed areas of the lower grip pad and upper and lower grip plates of each M/R blade for a crack and any corrosion. (ii) On the upper and lower exposed surfaces of each M/R blade from blade stations 24.5 to 35 for the chord width, visually inspect each layered doubler and blade skin for a crack and any corrosion. Pay particular attention for any cracking in a doubler or skin near or at the same blade station as the blade retention bolt hole (blade station 28). (iii) Visually inspect the exposed areas of each bond line at the edges of the lower grip pad, upper and lower grip plates, and each layered doubler (bond lines) on the upper and lower surfaces of each M/R blade for the entire length and chord width for an edge void, any corrosion, loose or damaged adhesive squeeze-out, and an edge delamination. Pay particular attention to any crack in the paint finish that follows the outline of a grip pad, grip plate, or doubler, and to any loose or damaged adhesive squeeze-out, as these may be the indication of an edge void. (2) If there is a crack, any corrosion, an edge void, loose or damaged adhesive squeeze-out, or an edge delamination during any inspection in paragraph (f)(1) of this AD, before further flight, do the following: (i) If there is a crack in a grip pad or any grip plate or doubler, replace the M/R blade with an airworthy M/R blade. (ii) If there is a crack in the M/R blade skin that is within maximum repair damage limits, repair the M/R blade. If the crack exceeds maximum repair damage limits, replace the M/R blade with an airworthyM/R blade. (iii) If there is any corrosion within maximum repair damage limits, repair theM/R blade. If the corrosion exceeds maximum repair damage limits, replace the M/R blade with an airworthy M/R blade. (iv) If there is an edge void in the grip pad or in a grip plate or doubler, determine the length and depth using a feeler gauge. Repair the M/R blade if the edge void is within maximum repair damage limits, or replace the M/R blade with an airworthy M/R blade. (v) If there is an edge void in a grip plate or doubler near the outboard tip, tap inspect the affected area to determine the size and shape of the void. Repair the M/R blade if the edge void is within maximum repair damage limits, or replace the M/R blade with an airworthy M/R blade. (vi) If there is any loose or damaged adhesive squeeze-out along any of the bond lines, trim or scrape away the adhesive without damaging the adjacent surfaces or parent material of the M/R blade. Determine if there is an edge void or any corrosion by lightly sanding the trimmed area smooth using 280 or finer grit paper. If there is no edge void or corrosion, refinish the sanded area. (vii) If there is an edge delamination along any of the bond lines or a crack in the paint finish, determine if there is an edge void or a crack in the grip pad, grip plate, doubler, or skin by removing paint from the affected area by lightly sanding in a span-wise direction using 180-220 grit paper. If there are no edge voids and no cracks, refinish the sanded area. (viii) If any parent material is removed during any sanding or trimming in paragraphs (f)(2)(vi) or (f)(2)(vii) of this AD, repair the M/R blade if the damage is within maximum repair damage limits, or replace the M/R blade with an airworthy M/R blade.
Required actions
Special flight permits are prohibited.
Unsafe condition
You are responsible for performing each action required by this AD within the specified compliance time unless it has already been accomplished prior to that time.
Affected ADs
This AD defines the unsafe condition as a crack in an M/R blade, which could result in failure of an M/R blade and subsequent loss of helicopter control.
Read the original on the Federal Register →
You just looked this one up by hand
TrackAD holds all 12,278 of them and matches them against the aircraft you actually look after — airframe, engine, propeller and appliances in one pass — then works out what falls due and when.
- Bring your existing list in from a spreadsheet Paste the rows straight out of Excel. Headers like C/W Date and N/A are read for you.
- A copy that works when this does not One file. No internet, no login, no this software running. For the morning something has to be produced and the computer is not cooperating.
- $5 a month, or $50 a year Up to 50 aircraft on either.
Look round a real shop first Start free
The demonstration shop is eleven real aircraft with a year of work behind them. No account needed.
The directive text above is reproduced from the Federal Register, a work of the United States government and in the public domain. The separation into applicability, compliance and required actions is TrackAD's.*1