Airworthiness directives › 2017-04-08
AD 2017-04-08 Airworthiness Directives; The Boeing Company Airplanes
Models named: 737-100, -200, -200C, -300, -400, -500 series. Read the applicability below — it usually turns on serial or part numbers too.
Applicability*9
(1) This AD applies to The Boeing Company Model 737-100, -200, -200C, -300, -400, and -500 series airplanes, certificated in any category, as identified in Boeing Alert Service Bulletin 737-53A1261, Revision 1, dated January 30, 2015. (2) Installation of Supplemental Type Certificate (STC) ST01219SE (http://rgl.faa.gov/Regulatory_and_Guidance_Library/rgstc.nsf/0/BE866B732F6CF31086257B9700692796?OpenDocument&Highlight=st01219se ) does not affect the ability to accomplish the actions required by this AD. Therefore, for airplanes on which STC ST01219SE is installed, a ”change in product” alternative method of compliance (AMOC) approval request is not necessary to comply with the requirements of 14 CFR 39.17.
Compliance
Comply with this AD within the compliance times specified, unless already done.
Required actions
(1) For Groups 1 through 3, Configurations 1, 3, 4, and 5 airplanes; Group 7, Configurations 1, 3, 4, and 5 airplanes; Groups 4 through 6, Configurations 1, 3, 4, and 6 airplanes; and Groups 8 through 11, Configurations 1, 3, 4, and 6 airplanes; as identified in Boeing Alert Service Bulletin 737-53A1261, Revision 1, dated January 30, 2015: Do the actions specified in paragraphs (g)(1)(i) and (g)(1)(ii) of this AD, and all applicable corrective actions, in accordance with the Accomplishment Instructions of Boeing Alert Service Bulletin 737-53A1261, Revision 1, dated January 30, 2015, except as required by paragraph (i)(3) of this AD. Do all applicable corrective actions before further flight. (i) At the applicable time specified in Tables 1, 2, 3, 5, 6, and 8 of paragraph 1.E., “Compliance,” of Boeing Alert Service Bulletin 737-53A1261, Revision 1, dated January 30, 2015, except as required by paragraphs (i)(1) and (i)(2) of this AD: Do medium frequency eddy current inspections for cracking of the upper-frame-to-side-frame splice of the fuselage. (ii) Repeat the inspections specified in paragraph (g)(1)(i) of this AD at the applicable time specified in Tables 1, 2, 3, 5, 6, and 8 of paragraph 1.E., “Compliance,” of Boeing Alert Service Bulletin 737-53A1261, Revision 1, dated January 30, 2015, until the preventive modification required by paragraph (k) of this AD, or a terminating action specified in paragraph (l) of this AD, has been accomplished. The inspections are terminated for the repaired or modified areas only. (2) For Groups 4 through 6, Configurations 2 and 5 airplanes; and Groups 8 through 11, Configurations 2 and 5 airplanes; as identified in Boeing Alert Service Bulletin 737-53A1261, Revision 1, dated January 30, 2015: Do the actions specified in paragraphs (g)(2)(i) and (g)(2)(ii) of this AD, and all applicable corrective actions, in accordance with the Accomplishment Instructions of Boeing Alert Service Bulletin 737-53A1261, Revision 1, dated January 30, 2015, except as required by paragraph (i)(3) of this AD. Do all applicable corrective actions before further flight. (i) At the applicable time specified in Tables 4 and 7 of paragraph 1.E., “Compliance,” of Boeing Alert Service Bulletin 737-53A1261, Revision 1, dated January 30, 2015, except as required by paragraphs (i)(1) and (i)(2) of this AD: Do a detailed inspection to determine if the existing frame repair meets all requirements specified in Boeing Alert Service Bulletin 737-53A1261, Revision 1, dated January 30, 2015, and for any frame repair that does meet all requirements, do detailed and high frequency eddy current (HFEC) inspections for cracking of the existing frame repairs. (ii) Repeat the inspections for cracking specified in paragraph (g)(2)(i) of this AD at the applicable time specified in Tables 4 and 7 of paragraph 1.E., “Compliance,” of Boeing Alert Service Bulletin 737-53A1261, Revision 1, dated January 30, 2015.
Unsafe condition
This AD was prompted by reports of additional fatigue cracking of the upper-frame-to-side-frame splice of the fuselage, and one report of a severed frame due to susceptibility to widespread fatigue damage (WFD). We are issuing this AD to detect and correct fatigue cracking of the upper-frame-to-side-frame splice of the fuselage, which could result in reduced structural integrity of the frame and adjacent lap joint, causing increased loading in the fuselage skin, which will accelerate skin crack growth and could result in decompression of the airplane.
Affected ADs
This AD replaces AD 2008-13-12 R1, Amendment 39-15719 (73 FR 67383, November 14, 2008) (“AD 2008-13-12 R1”).
Read the original on the Federal Register →
You just looked this one up by hand
TrackAD holds all 12,278 of them and matches them against the aircraft you actually look after — airframe, engine, propeller and appliances in one pass — then works out what falls due and when.
- Bring your existing list in from a spreadsheet Paste the rows straight out of Excel. Headers like C/W Date and N/A are read for you.
- A copy that works when this does not One file. No internet, no login, no this software running. For the morning something has to be produced and the computer is not cooperating.
- $5 a month, or $50 a year Up to 50 aircraft on either.
Look round a real shop first Start free
The demonstration shop is eleven real aircraft with a year of work behind them. No account needed.
The directive text above is reproduced from the Federal Register, a work of the United States government and in the public domain. The separation into applicability, compliance and required actions is TrackAD's.*1