Airworthiness directives › 2021-20-01
AD 2021-20-01 Airworthiness Directives; Pratt & Whitney Turbofan Engines
Applicability*9
This AD applies to Pratt & Whitney PW1519G, PW1521G, PW1521G-3, PW1521GA, PW1524G, PW1524G-3, PW1525G, PW1525G-3, PW1919G, PW1921G, PW1922G, PW1923G, and PW1923G-A model turbofan engines with a high-pressure turbine (HPT) 1st-stage hub, part number (P/N) 30G5701, or an HPT rotor 1st-stage blade retaining plate, P/N 30G1692, installed.
Compliance
Comply with this AD within the compliance times specified, unless already done.
Required actions
(1) For PW1519G, PW1521G, PW1521G-3, PW1521GA, PW1524G, and PW1524G-3 model turbofan engines: (i) For an affected HPT 1st-stage hub and an affected HPT rotor 1st-stage blade retaining plate with 3,000 cycles since new (CSN) or fewer on the effective date of this AD, before the affected part exceeds 4,700 CSN, remove the affected part, as applicable, and replace with a part eligible for installation. (ii) For an affected HPT 1st-stage hub and an affected HPT rotor 1st-stage blade retaining plate with greater than 3,000 CSN but fewer than 4,960 CSN on the effective date of the AD, at the next engine shop visit after accumulating 4,700 CSN or before the affected part exceeds 5,260 CSN, whichever occurs first, remove the affected part, as applicable, and replace with a part eligible for installation. (iii) For an affected HPT 1st-stage hub and an affected HPT rotor 1st-stage blade retaining plate with 4,960 CSN or greater on the effective date of the AD, at the next engine shop visit or within 300 cycles after the effective date of this AD, whichever occurs first, remove the affected part, as applicable, and replace with a part eligible for installation. (2) For PW1919G and PW1921G model turbofan engines: (i) For an affected HPT 1st-stage hub and an affected HPT rotor 1st-stage blade retaining plate with 3,000 CSN or fewer on the effective date of this AD, before the affected part exceeds 4,700 CSN, remove the affected part, as applicable, and replace with a part eligible for installation. (ii) For an affected HPT 1st-stage hub and an affected HPT rotor 1st-stage blade retaining plate with greater than 3,000 CSN but fewer than 4,700 CSN on the effective date of the AD, at the next engine shop visit after the affected part accumulates 4,700 CSN or before the affected part exceeds 5,000 CSN, whichever occurs first, remove the affected part, as applicable, and replace with a part eligible for installation. (iii) For an affected HPT 1st-stage hub and an affected HPT rotor 1st-stage blade retaining plate with 4,700 CSN or greater on the effective date of the AD, at the next engine shop visit or within 300 cycles after the effective date of this AD, whichever occurs first, remove the affected part, as applicable, and replace with a part eligible for installation. (3) For PW1525G and PW1525G-3 model turbofan engines: (i) Before the affected HPT 1st-stage hub and affected HPT rotor 1st-stage blade retaining plate exceeds 2,800 CSN, respectively, or within 300 cycles after the effective date of this AD, whichever occurs later, remove the affected part, as applicable, and replace with a part eligible for installation. (ii) [Reserved] (4) For PW1922G, PW1923G, and PW1923G-A model turbofan engines: (i) Before the affected HPT 1st-stage hub and affected HPT rotor 1st-stage blade retaining plate exceeds 3,000 CSN, respectively, or within 300 cycles after the effective date of this AD, whichever occurs later, remove the affected part, as applicable, and replace with a part eligible for installation. (ii) [Reserved]
Unsafe condition
This AD was prompted by a report from the manufacturer who determined that the HPT 1st-stage hub and HPT rotor 1st-stage blade retaining plate fail to meet the published life-cycle limits for each part. The FAA is issuing this AD to prevent failure of the HPT 1st-stage hub or HPT rotor 1st-stage blade retaining plate. The unsafe condition, if not addressed, could result in the release of the HPT 1st-stage hub or HPT rotor 1st-stage blade retaining plate, damage to the engine, and damage to the aircraft.
Affected ADs
None.
Read the original on the Federal Register →
You just looked this one up by hand
TrackAD holds all 12,278 of them and matches them against the aircraft you actually look after — airframe, engine, propeller and appliances in one pass — then works out what falls due and when.
- Bring your existing list in from a spreadsheet Paste the rows straight out of Excel. Headers like C/W Date and N/A are read for you.
- A copy that works when this does not One file. No internet, no login, no this software running. For the morning something has to be produced and the computer is not cooperating.
- $5 a month, or $50 a year Up to 50 aircraft on either.
Look round a real shop first Start free
The demonstration shop is eleven real aircraft with a year of work behind them. No account needed.
The directive text above is reproduced from the Federal Register, a work of the United States government and in the public domain. The separation into applicability, compliance and required actions is TrackAD's.*1