TrackAD

Airworthiness directives › 2021-21-06

AD 2021-21-06 Airworthiness Directives; Hélicoptères Guimbal Helicopters

2021-12-17
2021-11-12
—
—
Airframe
—

Makes named: guimbal. Models named: Cabri G2. Read the applicability below — it usually turns on serial or part numbers too.

Applicability*9

This AD applies to Hélicoptères Guimbal (HG) Model Cabri G2 helicopters, certificated in any category, the following aluminum cooling fan (cooling fan) part number (P/N) installed: (1) P/N G52-00-000, (2) P/N G52-00-001 or P/N G52-04-100, if it is or has previously been mounted on a 12-hole engine pulley P/N G52-10-100 or P/N G52-10-101.

Compliance

Comply with this AD within the compliance times specified, unless already done.

Required actions

(1) For Model Cabri G2 helicopters with cooling fan P/N G52-00-000 installed, within 150 hours time-in-service (TIS) after the effective date of this AD: (i) Remove the cooling fan from service by following the Required Actions, Cooling Fan Removal, paragraphs (a) through (g), of Guimbal Service Bulletin SB 16-021 E, dated August 27, 2019 (SB 16-021 Rev E), except you are not required to discard any parts. (ii) Install the improved cooling fan P/N G52-04-101 by following the Required Actions, Cooling Fan Installation, paragraphs (a) through (j), of SB 16-021 Rev E. (2) For Model Cabri G2 helicopters with a cooling fan P/N G52-00-001 or P/N G52-04-100 that is mounted or was previously mounted on a 12-hole engine pulley P/N G52-10-100 or P/N G52-10-101, and with 1,500 or more total hours TIS, since first installation on a helicopter, within 150 hours TIS after the effective date of this AD: (i) Remove the cooling fan from service by following the Required Actions, Cooling Fan Removal, paragraphs (a) through (g), of SB 16-021 Rev E, except you are not required to discard any parts, or remove the cooling fan by following the Required Actions, Cooling Fan Removal, paragraphs (a) through (g), of SB 16-021 Rev E and modify the cooling fan by following the Required Actions, Cooling Fan Retrofit, paragraphs (a) through (h) of SB 16-021 Rev E. (ii) Install the improved cooling fan P/N G52-04-101 by following the Required Actions, Cooling Fan Installation, paragraphs (a) through (j), of SB 16-021 Rev E. (3) For Model Cabri G2 helicopters with a cooling fan P/N G52-00-001 or P/N G52-04-100 that is mounted or was previously mounted on a 12-hole engine pulley P/N G52-10-100 or P/N G52-10-101 and with 500 total hours TIS but with less than 1,500 total hours TIS, since first installation on a helicopter, within 500 hours TIS after the effective date of this AD, perform the actions required by paragraphs (g)(2)(i) and (ii) of this AD. (4) For Model Cabri G2 helicopters with a cooling fan P/N G52-00-001 or P/N G52-04-100 that is mounted or was previously mounted on a 12-hole engine pulley P/N G52-10-100 or P/N G52-10-101 and with less than 500 total hours TIS since first installation on a helicopter, within 1,000 hours TIS after the effective date of this AD, perform the actions required by paragraphs (g)(2)(i) and (ii) of this AD. (5) As of the effective date of this AD, do not install any cooling fan listed in paragraph (c) of this AD on any helicopter.

Unsafe condition

This AD was prompted by a report of an in-flight engine shutdown due to a crack and subsequent failure of the cooling fan. The FAA is issuing this AD to prevent failure of the cooling fan. This condition, if not addressed, could result in an in-flight engine shut-down and loss of control of the helicopter.

Affected ADs

None.

Read the original on the Federal Register →

You just looked this one up by hand

TrackAD holds all 12,278 of them and matches them against the aircraft you actually look after — airframe, engine, propeller and appliances in one pass — then works out what falls due and when.

Look round a real shop first Start free

The demonstration shop is eleven real aircraft with a year of work behind them. No account needed.

The directive text above is reproduced from the Federal Register, a work of the United States government and in the public domain. The separation into applicability, compliance and required actions is TrackAD's.*1