AD 2022-04-06 Airworthiness Directives; Bell Textron Canada Limited Helicopters

Models named: 505. Read the applicability below — it usually turns on serial or part numbers too.

This AD applies to Bell Textron Canada Limited Model 505 helicopters, serial number (S/N) 65011 through 65347 inclusive, certificated in any category.

Comply with this AD within the compliance times specified, unless already done.

(1) From March 31, 2021 (the effective date of AD 2021-06-06), before further flight, revise the Limitations section of the existing Rotorcraft Flight Manual (RFM) for your helicopter by inserting Bell 505 RFM Temporary Revision (TR) for Pilot Collective (ASB 505-21-20), BHT-505-FM-1, Temporary Revision (TR-6) or Bell 505 RFM TR for Pilot Collective (ASB 505-21-20), BHT-505-FM-2, Temporary Revision (TR-1), each dated March 3, 2021, as applicable to your helicopter. Using a different document with information identical to the information for the “Flight Crew” and “Configuration,” as applicable to your helicopter, in the RFM TR specified in this paragraph for your helicopter is acceptable for compliance with the requirements of this paragraph. This action may be performed by the owner/operator (pilot) holding at least a private pilot certificate and must be entered into the aircraft records showing compliance with this AD in accordance with 14 CFR 43.9(a)(1) through (4) and 14 CFR 91.417(a)(2)(v). The record must be maintained as required by 14 CFR 91.417 or 135.439. (2) Before further flight after the effective date of this AD, and thereafter at intervals not to exceed 25 hours time-in-service (TIS): (i) Remove the pilot collective stick and grip assembly from the jackshaft assembly and clean the areas specified in Figure 2 of Bell Alert Service Bulletin 505-21-20, Revision C, dated March 11, 2021 (ASB 505-21-20 Rev C) with a clean cloth C-516C or equivalent moistened with dry cleaning solvent C-304 or equivalent. (ii) Perform a fluorescent penetrant inspection (FPI) for a crack by following the Accomplishment Instructions, Part I, paragraph 5. (but not paragraphs 5.a. and b.) of ASB 505-21-20 Rev C. Perform this FPI in the areas specified in Figure 2 of ASB 505-21-20 Rev C. If there is a crack, before further flight, remove the pilot collective stick and grip assembly from service. (3) Within 12 months after the effective date of this AD, remove the pilot collective stick tube from service and install pilot collective stick tube part number (P/N) M207-20M301-043 by following the Accomplishment Instructions, Part II, paragraphs 3. and 4. of ASB 505-21-20 Rev C except where this service information specifies discarding parts, you are required to remove those parts from service instead. Thereafter, remove from service pilot collective stick tube P/N M207-20M301-043 before it accumulates 6,250 total hours TIS. (4) Completing the actions required in paragraph (g)(3) of this AD constitutes a terminating action for the requirements in paragraphs (g)(1) and (2) of this AD. (5) As of the effective date of this AD, do not install any pilot collective stick and grip assembly on any helicopter unless the actions required by paragraphs (g)(2) and (3) of this AD have been accomplished. (6) As of the effective date of this AD, relief under any Master Minimum Equipment List or Minimum Equipment List for the Audio Panel is prohibited when the aircraft is operated with a single pilot from the left seat.

This AD was prompted by a report of a cracked pilot collective stick and grip assembly. The FAA is issuing this AD to detect a cracked pilot collective stick and grip assembly. The unsafe condition, if not addressed, could result in failure of the pilot collective stick and grip assembly and subsequent loss of control of the helicopter.

This AD replaces AD 2021-06-06, Amendment 39-21473 (86 FR 14366, March 16, 2021) (AD 2021-06-06).