TrackAD

Airworthiness directives › 2022-16-07

AD 2022-16-07 Airworthiness Directives; Airbus SAS Airplanes

Superseded. This directive was replaced by AD 2024-08-05. Work to the current one.
2022-09-27
2022-08-23
—
—
Airframe
2024-08-05

Models named: A330-201, -202, -203, -223, -223F, -243, -243F, -301, -302, -303. Read the applicability below — it usually turns on serial or part numbers too.

Applicability*9

This AD applies to Airbus SAS Model A330-201, -202, -203, -223, -223F, -243, -243F, -301, -302, -303, -321, -322, -323, -341, -342, -343, -841, and -941 airplanes, certificated in any category, with an original airworthiness certificate or original export certificate of airworthiness issued on or before July 1, 2021.

Compliance

Comply with this AD within the compliance times specified, unless already done.

Required actions

This paragraph restates the requirements of paragraph (g) of AD 2019-21-02, with no changes. For Model A330-201, -202, -203, -223, -223F, -243, -243F, -301, -302, -303, -321, -322, -323, -341, -342, and -343 airplanes with an original airworthiness certificate or original export certificate of airworthiness issued on or before October 15, 2018: Within 90 days after November 29, 2019 (the effective date of AD 2019-21-02), revise the existing maintenance or inspection program, as applicable, to incorporate the information specified in Airbus A330 Airworthiness Limitations Section (ALS) Part 3—Certification Maintenance Requirements (CMR), Revision 06, dated October 15, 2018, as supplemented by Airbus A330 ALS Part 3—Certification Maintenance Requirements (CMR), Variation 6.1, dated June 28, 2019. The initial compliance times for doing the tasks is at the time specified in Airbus A330 Airworthiness Limitations Section (ALS) Part 3—Certification Maintenance Requirements (CMR), Revision 06, dated October 15, 2018, as supplemented by Airbus A330 ALS Part 3—Certification Maintenance Requirements (CMR), Variation 6.1, dated June 28, 2019, or within 90 days after November 29, 2019, whichever occurs later. Accomplishing the revision of the existing maintenance or inspection program required by paragraph (i) of this AD terminates the requirements of this paragraph.

Unsafe condition

This AD was prompted by a determination that new or more restrictive airworthiness limitations are necessary, and that new airplanes have been added to the applicability. The FAA is issuing this AD to address a safety-significant latent failure (that is not annunciated) that, in combination with one or more other specific failures or events, could result in a hazardous or catastrophic failure condition.

Affected ADs

This AD replaces AD 2016-26-05, Amendment 39-18763 (82 FR 1170, January 5, 2017) (AD 2016-26-05); and AD 2019-21-02, Amendment 39-19768 (84 FR 57313, October 25, 2019) (AD 2019-21-02).

Read the original on the Federal Register →

You just looked this one up by hand

TrackAD holds all 12,278 of them and matches them against the aircraft you actually look after — airframe, engine, propeller and appliances in one pass — then works out what falls due and when.

Look round a real shop first Start free

The demonstration shop is eleven real aircraft with a year of work behind them. No account needed.

The directive text above is reproduced from the Federal Register, a work of the United States government and in the public domain. The separation into applicability, compliance and required actions is TrackAD's.*1