TrackAD

Airworthiness directives › 2023-15-07

AD 2023-15-07 Airworthiness Directives; Air Tractor, Inc. Airplanes

Superseded. This directive was replaced by AD 2024-16-06. Work to the current one.
2023-08-09
2023-08-09
—
—
Airframe
2024-16-06

Models named: AT-802, AT-802A. Read the applicability below — it usually turns on serial or part numbers too.

Applicability*9

This AD applies to Air Tractor, Inc. Model AT-802 and AT-802A airplanes, all serial numbers, certificated in any category, that have Wipaire, Inc. Supplemental Type Certificate (STC) No. SA01795CH installed.

Compliance

Comply with this AD within the compliance times specified, unless already done.

Required actions

(1) At the compliance times in paragraphs (g)(1)(i) through (iii) of this AD, as applicable, and thereafter at intervals not to exceed 200 hours time-in-service (TIS), inspect the left and right forward horizontal stabilizer spars for cracks in accordance with Steps 1 through 9 of the Work Instructions of Wipaire, Inc. Service Letter 253, Revision B, dated July 27, 2023. (i) For STC configuration 7D1-4399-01: Within 3 days or 24 hours TIS after the effective date of this AD or before the accumulation of 200 hours TIS since installation of STC No. SA01795CH, whichever occurs later. (ii) For STC configuration 7D1-4399-02: Within 5 days or 24 hours TIS after the effective date of this AD or before the accumulation of 300 hours TIS since installation of STC No. SA01795CH, whichever occurs later. (iii) For STC configuration 7D1-4399-03: Within 15 days or 24 hours TIS after the effective date of this AD or before the accumulation of 600 hours TIS since installation of STC No. SA01795CH, whichever occurs later. (2) If any crack is found in a forward horizontal stabilizer spar during any inspection required by paragraph (g)(1) of this AD, before further flight, replace the cracked forward horizontal stabilizer spar. Replacement of the cracked forward horizontal stabilizer spar starts the initial and repetitive inspections over. (3) Within 10 days after each inspection required by paragraph (g)(1) of this AD or within 10 days after the effective date of this AD, whichever occur later, report the following to the FAA at the address in paragraph (j)(1) of this AD. Report this information regardless of whether cracks are found. (i) Model, engine configuration (with horsepower limits), and propeller type; (ii) Serial number and N number; (iii) Total hours TIS on airframe; (iv) Total hours TIS operated with floats, if known; (v) STC configuration and total hours with STC installed; (vi) Crack location (right or left, upper/lower caps inboard/outboard hole); (vii) Crack size; (viii) Photos of cracks found, if available; and (ix) Any additional operator/mechanic comments

Unsafe condition

This AD was prompted by reports of cracks found in at least one forward horizontal stabilizer spar on 24 of the affected airplanes where the vertical finlets tie to the forward horizontal stabilizer spar. The FAA is issuing this AD to prevent structural failure of the forward horizontal stabilizer spars. The unsafe condition, if not addressed, could result in structural failure of the horizontal tail with consequent loss of control of the airplane.

Affected ADs

None.

Read the original on the Federal Register →

You just looked this one up by hand

TrackAD holds all 12,278 of them and matches them against the aircraft you actually look after — airframe, engine, propeller and appliances in one pass — then works out what falls due and when.

Look round a real shop first Start free

The demonstration shop is eleven real aircraft with a year of work behind them. No account needed.

The directive text above is reproduced from the Federal Register, a work of the United States government and in the public domain. The separation into applicability, compliance and required actions is TrackAD's.*1