AD 95-11-05 Airworthiness Directives; Societe Nationale Industrielle Aerospatiale and Eurocopter France Model AS-355 E, F, F1, F2, and N Helicopters

Models named: AS-355 E, F, F1, F2, N. Read the applicability below — it usually turns on serial or part numbers too.

Model AS-355 E, F, F1, F2, and N helicopters, with main gearbox (MGB) oil pressure switch (switch), part number (P/N) 704A37-721-082 (S1130-021-082), modification number 350A07- 7141, installed, certificated in any category. Note 1: This AD applies to each helicopter identified in the preceding applicability provision, regardless of whether it has been modified, altered, or repaired in the area subject to the requirements of this AD. For helicopters that have been modified, altered, or repaired so that the performance of the requirements of this AD is affected, the owner/operator must use the authority provided in paragraph (d) to request approval from the FAA. This approval may address either no action, if the current configuration eliminates the unsafe condition, or different actions necessary to address the unsafe condition described in this AD. Such a request should include an assessment of the effect of the changed configuration on the unsafe condition addressed by this AD. In no case does the presence of any modification, alteration, or repair remove any helicopter from the applicability of this AD.

Required as indicated, unless accomplished previously. To prevent an undetected loss of oil pressure, loss of the MGB, loss of power to the main rotor system, and subsequent loss of control of the helicopter, accomplish the following: (a) Until the MGB switch installation required by paragraph (c) of this AD is accomplished, during each shutdown of the helicopter engine, check to ensure that the MGB pressure warning light illuminates. If it does not illuminate, before further flight, replace the MGB switch in accordance with paragraph (c) of this AD. (b) The operational check required by paragraph (a) of this AD may be performed by an owner/operator holding at least a private pilot certificate and must be entered into the aircraft records showing compliance with this AD in accordance with 14 CFR sections 43.11 and 91.417(a)(2)(v). (c) Within 30 days after the effective date of this AD, remove the MGB switch, P/N 704A37-721-082 (S1130-021-082), modification number 350A07-7141, and replace with MGB switch, P/N 704A37-721-089 (S1130-021-089), modification number 350A07-7152, or Jaeger MGB switch, P/N 704A37-721-014 (068651.54/350A32-3134-00) in accordance with paragraph CC(1) of [[Page 27686]] Eurocopter Service Bulletin AS 355, No. 01.39, Revision 1, dated April 21, 1994. Note 2: The MGB switch P/N is engraved on the MGB switch casing. (d) An alternative method of compliance or adjustment of the compliance time that provides an acceptable level of safety may be used when approved by the Manager, Rotorcraft Standards Staff, FAA, Rotorcraft Directorate. Operators shall submit their requests through an FAA Principal Maintenance Inspector, who may concur or comment and then send it to the Manager, Rotorcraft Standards Staff. Note 3: Information concerning the existence of approved alternative methods of compliance with this AD, if any, may be obtained from the Rotorcraft Standards Staff. (e) The check, removal, and replacement shall be done in accordance with Eurocopter Service Bulletin AS 355 No. 01.39, Revision 1, dated April 21, 1994. This incorporation by reference was approved by the Director of the Federal Register in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. Copies may be obtained from American Eurocopter Corporation, 2701 Forum Drive, Grand Prairie, Texas 75053-4005. Copies may be inspected at the FAA, Office of the Assistant Chief Counsel, 2601 Meacham Blvd., Room 663, Fort Worth, Texas 76137; or at the Office of the Federal Register, 800 North Capitol Street, NW., suite 700, Washington, DC. (f) This amendment becomes effective on June 9, 1995. Issued in Fort Worth, Texas, on May 17, 1995. Eric Bries, Acting Manager, Rotorcraft Directorate, Aircraft Certification Service. [FR Doc. 95-12607 Filed 5-24-95; 8:45 am] BILLING CODE 4910-13-P]