Airworthiness directives › 95-21-12
AD 95-21-12 Airworthiness Directives; Eurocopter Deutschland GmbH (ECD) Model MBB-BK 117 A-1, A-3, A-4, B-1, B-2, and C-1 Helicopters
Models named: MBB-BK 117 A-1, A-3, A-4, B-1, B-2, C- 1. Read the applicability below — it usually turns on serial or part numbers too.
Applicability*9
Model MBB-BK 117 A-1, A-3, A-4, B-1, B-2, and C- 1 helicopters, certificated in any category. Note 1: This AD applies to each helicopter identified in the preceding applicability provision, regardless of whether it has been modified, altered, or repaired in the area subject to the requirements of this AD. For helicopters that have been modified, altered, or repaired so that the performance of the requirements of this AD is affected, the owner/operator must use the authority provided in paragraph (d) to request approval from the FAA. This approval may address either no action, if the current configuration eliminates the unsafe condition, or different actions necessary to address the unsafe condition described in this AD. Such a request should include an assessment of the effect of the changed configuration on the unsafe condition addressed by this AD. In no case does the presence of any modification, alteration, or repair remove any helicopter from the applicability of this AD.
Compliance
Required as indicated, unless accomplished previously. To detect movement of a balance weight and to prevent severe vibrations and a subsequent precautionary landing, accomplish the following: (a) Within the next 5 hours time-in-service (TIS) after the effective date of this AD, and thereafter, at intervals not to exceed 50 hours TIS, visually inspect the upper and lower surfaces of the main rotor blades (blades) in the area of the outboard lead balance weight in the marked inspection area for signs of bulging, in accordance with Paragraph 2.A. of the Accomplishment Instructions of Eurocopter Deutschland GmbH (ECD) Alert Service Bulletin ASB-MBB- BK 117-10-108, Revision 1, dated October 14, 1994. (b) If a marked inspection area is not visible, mark the area in accordance with Paragraph 2.A. of the Accomplishment Instructions of Eurocopter Deutschland GmbH (ECD) Alert Service Bulletin ASB-MBB-BK 117-10-108, Revision 1, dated October 14, 1994, and then inspect in accordance with paragraph (a) of this AD. (c) If bulging exceeds 1mm (0.040 inch) in height, remove the blade and replace it with an airworthy blade in accordance with the applicable maintenance manual. (d) An alternative method of compliance or adjustment of the compliance time that provides an acceptable level of safety may be used when approved by the Manager, FAA, Rotorcraft Directorate, Rotorcraft Standards Staff. Operators shall submit their requests through an FAA Principal Maintenance Inspector, who may concur or comment and then send it to the Manager, Rotorcraft Standards Staff. Note 2: Information concerning the existence of approved alternative methods of compliance with this AD, if any, may be obtained from the Rotorcraft Standards Staff. (e) Special flight permits may be issued in accordance with sections 21.197 and 21.199 of the Federal Aviation Regulations (14 CFR 21.197 and 21.199) to operate the helicopter to a location where the requirements of this AD can be accomplished. (f) The inspection and replacement, if necessary, shall be done in accordance with Eurocopter Deutschland GmbH (ECD) Alert Service Bulletin ASB-MBB-BK 117-10-108, Revision 1, dated October 14, 1994. This incorporation by reference was approved by the Director of the Federal Register in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. Copies may be obtained from American Eurocopter Corporation, 2701 Forum Drive, Grand Prairie, Texas 75053-4005. Copies may be inspected at the FAA, Office of the Assistant Chief Counsel, 2601 Meacham Blvd., Room 663, Fort Worth, Texas; or at the Office of the Federal Register, 800 North Capitol Street, NW., suite 700, Washington, DC. (g) This amendment becomes effective on November 20, 1995. Issued in Fort Worth, Texas, on October 4, 1995. Daniel P. Salvano, Manager, Rotorcraft Directorate, Aircraft Certification Service. [FR Doc. 95-25522 Filed 10-13-95; 8:45 am] BILLING CODE 4910-13-U
Read the original on the Federal Register →
You just looked this one up by hand
TrackAD holds all 12,278 of them and matches them against the aircraft you actually look after — airframe, engine, propeller and appliances in one pass — then works out what falls due and when.
- Bring your existing list in from a spreadsheet Paste the rows straight out of Excel. Headers like C/W Date and N/A are read for you.
- A copy that works when this does not One file. No internet, no login, no this software running. For the morning something has to be produced and the computer is not cooperating.
- $5 a month, or $50 a year Up to 50 aircraft on either.
Look round a real shop first Start free
The demonstration shop is eleven real aircraft with a year of work behind them. No account needed.
The directive text above is reproduced from the Federal Register, a work of the United States government and in the public domain. The separation into applicability, compliance and required actions is TrackAD's.*1