AD 98-07-09 Airworthiness Directives; Bell Helicopter Textron, Inc. Model 47B, 47B-3, 47D, 47D-1, 47G, 47G-2, 47G-2A, 47G-2A-1, 47G-3, 47G-3B, 47G-3B-1, 47G-3B-2, 47G-3B-2A, 47G-4, 47G-4A, 47G-5, 47G-5A, 47H-1, 47J, 47J-2, 47J-2A, and 47K Helicopters

Model 47B, 47B-3, 47D, 47D-1, 47G, 47G-2, 47G-2A, 47G-2A-1, 47G-3, 47G-3B, 47G-3B-1, 47G-3B-2, 47G-3B-2A, 47G-4, 47G- 4A, 47G-5, 47G-5A, 47H-1, 47J, 47J-2, 47J-2A, and 47K helicopters, certificated in any category. Note 1: This AD applies to each helicopter identified in the preceding applicability provision, regardless of whether it has been modified, altered, or repaired in the area subject to the requirements of this AD. For helicopters that have been modified, altered, or repaired so that the performance of the requirements of this AD is affected, the owner/operator must use the authority provided in paragraph (b) to request approval from the FAA. This approval may address either no action, if the current configuration eliminates the unsafe condition, or different actions necessary to address the unsafe condition described in this AD. Such a request should include an assessment of the effect of the changed configuration on the unsafe condition addressed by this AD. In no case does the presence of any modification, alteration, or repair remove any helicopter from the applicability of this AD.

Required within the next 100 hours time-in-service or within the next 120 [[Page 15756]] calendar days, whichever occurs first, unless accomplished previously. To prevent failure of the stabilizer bar damper link assembly, which can result in degraded control response and subsequent loss of control of the helicopter, accomplish the following: (a) Remove the stabilizer bar damper link assemblies from the helicopter, install a safety washer kit, part number (P/N) CA-047- 96-022-1, and reinstall the stabilizer bar damper link assemblies onto the helicopter in accordance with the Accomplishment Instructions contained in Bell Helicopter Textron, Inc. Alert Service Bulletin No. 47-96-22, dated August 16, 1996. (b) An alternative method of compliance or adjustment of the compliance time that provides an acceptable level of safety may be used if approved by the Manager, Rotorcraft Certification Office, Rotorcraft Directorate, FAA. Operators shall submit their requests through an FAA Principal Maintenance Inspector, who may concur or comment and then send it to the Manager, Rotorcraft Certification Office. Note 2: Information concerning the existence of approved alternative methods of compliance with this AD, if any, may be obtained from the Rotorcraft Certification Office. (c) Special flight permits may be issued in accordance with Secs. 21.197 and 21.199 of the Federal Aviation Regulations (14 CFR 21.197 and 21.199) to operate the helicopter to a location where the requirements of this AD can be accomplished. (d) The installation shall be done in accordance with Bell Helicopter Textron, Inc. Alert Service Bulletin No. 47-96-22, dated August 16, 1996. This incorporation by reference was approved by the Director of the Federal Register in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. Copies may be obtained from Bell Helicopter Textron, Inc., P.O. Box 482, Fort Worth, Texas 76101. Copies may be inspected at the FAA, Office of the Regional Counsel, Southwest Region, 2601 Meacham Blvd., Room 663, Fort Worth, Texas; or at the Office of the Federal Register, 800 North Capitol Street, NW., suite 700, Washington, DC. (e) This amendment becomes effective on May 6, 1998. Issued in Fort Worth, Texas, on March 24, 1998. Eric Bries, Acting Manager, Rotorcraft Directorate, Aircraft Certification Service. [FR Doc. 98-8466 Filed 3-31-98; 8:45 am] BILLING CODE 4910-13-U